Ibm Thinkpad 380 385 Disassembly Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 minutes

Sections

IBM ThinkPad 380/385 Disassembly
5 steps

Flags

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackIBM ThinkPad 380 and 385
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Remove battery and RAM

Orient the laptop as seen in the picture with the battery facing you on the bottom right. To remove the main battery, first pull up on the tab with the arrow, then push away from you. You can now lift the battery out by pulling towards you and out. Set aside.
Using a #1 Phillips bit, unscrew the door to the RAM and CMOS battery compartment. This is a captive screw. Once unscrewed enough, open the door, tilting towards you. Remove and set aside.
Using a plastic spudger, pop the CMOS coin cell battery out of its holder by inserting the spudger under the battery in the notch on the front and pull up. Careful, this thing flies. Hunt it down on the floor or wherever it flew to and set aside.
Release the RAM by pressing the clips outward. The RAM chip will pop up and can be lifted out. Set aside.

Orient the laptop as seen in the picture with the battery facing you on the bottom right. To remove the main battery, first pull up on the tab with the arrow, then push away from you. You can now lift the battery out by pulling towards you and out. Set aside.

Using a #1 Phillips bit, unscrew the door to the RAM and CMOS battery compartment. This is a captive screw. Once unscrewed enough, open the door, tilting towards you. Remove and set aside.

Using a plastic spudger, pop the CMOS coin cell battery out of its holder by inserting the spudger under the battery in the notch on the front and pull up. Careful, this thing flies. Hunt it down on the floor or wherever it flew to and set aside.

Release the RAM by pressing the clips outward. The RAM chip will pop up and can be lifted out. Set aside.

1024

Step 2

              Remove case screws

Using a #1 Phillips bit, remove the two (2) 8mm screws from the front left.
Using a #1 Phillips bit, remove the two (2) 6mm screws from the right side in the battery well.
Using a #1 Phillips bit, remove the single (1) 25mm screw from the center.
The following is only relevant if you need to remove the CD-ROM/FDD assembly, or HDD
Using a #1 Phillips bit, remove the two (2) 8mm screws from the middle left of the case.

Using a #1 Phillips bit, remove the two (2) 8mm screws from the front left.

Using a #1 Phillips bit, remove the two (2) 6mm screws from the right side in the battery well.

Using a #1 Phillips bit, remove the single (1) 25mm screw from the center.

The following is only relevant if you need to remove the CD-ROM/FDD assembly, or HDD

Using a #1 Phillips bit, remove the two (2) 8mm screws from the middle left of the case.

Step 3

              Remove keyboard

Before removing the keyboard, using a Plastic Spudger to slide the keyboard towards you and away from the screen assembly.
Once the keyboard is loosened, carefully lift it up from the front.
The keyboard is tethered by a safety clip to prevent damage to the ribbon cables.
Slide the safety clip to the side to release the keyboard.
Using a plastic spudger, gently release the bailers for all three (3) ribbon cables and slide them out.
You can now lift off the keyobard and set aside.

Before removing the keyboard, using a Plastic Spudger to slide the keyboard towards you and away from the screen assembly.

Once the keyboard is loosened, carefully lift it up from the front.

The keyboard is tethered by a safety clip to prevent damage to the ribbon cables.

Slide the safety clip to the side to release the keyboard.

Using a plastic spudger, gently release the bailers for all three (3) ribbon cables and slide them out.

You can now lift off the keyobard and set aside.

Step 4

              Remove CD-ROM/FDD Cage

Turn the laptop so it faces away from you. Using a #1 Phillips bit, remove only the top screw from the left side.
Using a #1 Phillips bit, remove the two (2) 6mm screws securing the drive cage. Note: there may only be one depending on your model.
Using a #1 Phillips bit, remove the single (1) 6mm screw (special head) from the top left corner of the drive assembly.
Using a #1 Phillips bit, remove the 6mm screw from the front of the drive assembly.
Using a plastic spudger, disconnect the ribbon cable in the center of the case attached to the drive assembly.
Part of the metal cage and drive assembly is secured under the fragile plastic of the case on the right side. You’re aim is to slide both out without stressing the plastic.
Carefully lift off the metal cage securing the drive assembly by lifting the left part and pulling outward. Set aside.
You are now able to remove the CD-ROM/FDD assembly. Be carefull that the laptop does not fall backwards when removing the assembly. Do this by tilting the left side up and sliding it out from the plastic case on the right side. Set aside.

Turn the laptop so it faces away from you. Using a #1 Phillips bit, remove only the top screw from the left side.

Using a #1 Phillips bit, remove the two (2) 6mm screws securing the drive cage. Note: there may only be one depending on your model.

Using a #1 Phillips bit, remove the single (1) 6mm screw (special head) from the top left corner of the drive assembly.

Using a #1 Phillips bit, remove the 6mm screw from the front of the drive assembly.

Using a plastic spudger, disconnect the ribbon cable in the center of the case attached to the drive assembly.

Part of the metal cage and drive assembly is secured under the fragile plastic of the case on the right side. You’re aim is to slide both out without stressing the plastic.

Carefully lift off the metal cage securing the drive assembly by lifting the left part and pulling outward. Set aside.

You are now able to remove the CD-ROM/FDD assembly. Be carefull that the laptop does not fall backwards when removing the assembly. Do this by tilting the left side up and sliding it out from the plastic case on the right side. Set aside.

Step 5

              Remove HDD

Turn the laptop so the back is facing you.
Using a #1 Phillips bit, remove the two (2) 6mm screws above the serial port and left side of the printer port.
Turn the laptop back around and open the screen. Using a #1 Phillips bit, remove the silver screw from the bottom left of the top hard drive case.
Remove the hard drive top enclosure by pulling back toward you and lifting up and out.
Carefully slide the hard drive to the right. This may take a little force so be carefull not to damage the capacitors on the right.
Once the drive is disconnected from the IDE connector, lift the right side up and remove. Set asside or replace.

Turn the laptop so the back is facing you.

Using a #1 Phillips bit, remove the two (2) 6mm screws above the serial port and left side of the printer port.

Turn the laptop back around and open the screen. Using a #1 Phillips bit, remove the silver screw from the bottom left of the top hard drive case.

Remove the hard drive top enclosure by pulling back toward you and lifting up and out.

Carefully slide the hard drive to the right. This may take a little force so be carefull not to damage the capacitors on the right.

Once the drive is disconnected from the IDE connector, lift the right side up and remove. Set asside or replace.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    Hrushka

Member since: 07/24/2021

1,370 Reputation

                                      7 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Hans Zarkov - Feb 27, 2022

Do you know how to fir that spring tensioner located in central left part of the picture showing internals after keyboard has been removed?

Grammar Police#

Bullets!#

In Progress#

Member-Contributed Guide#

What you need#

#

#

#

#

#

#

#

Grammar Police

Bullets!

In Progress

Member-Contributed Guide

What you need