Difficulty

Easy

Steps

13

Time Required

                          20 - 30 minutes

Sections

1

  • Strings
  • 13 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackIbanez 5 String Bass Model SR405QM

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Strings
  • Loosen all of the strings completely by turning each tuning peg counter clockwise. Continue until there is no tension in the strings

Loosen all of the strings completely by turning each tuning peg counter clockwise. Continue until there is no tension in the strings

1024

Step 2

  • Remove each string by pulling it out of the string tree at the top and through the bridge at the bottom.

Remove each string by pulling it out of the string tree at the top and through the bridge at the bottom.

Step 3

  • Thread the largest new string through the bridge hole farthest from the knobs. Hold it firmly in place.

Thread the largest new string through the bridge hole farthest from the knobs. Hold it firmly in place.

Step 4

  • Pull the string up to the corresponding string tree.

Pull the string up to the corresponding string tree.

Step 5

  • Firmly grasp the middle of the string and pull it taut.

Firmly grasp the middle of the string and pull it taut.

Step 6

  • On a taut string, measure one inch past the nut before using a pair of wire cutters to cut the string.

On a taut string, measure one inch past the nut before using a pair of wire cutters to cut the string.

Step 7

  • Take the end of the string and insert it into the hole in the middle of the string tree.

Take the end of the string and insert it into the hole in the middle of the string tree.

Step 8

  • Bend the string sideways into the channel of the string tree.

Bend the string sideways into the channel of the string tree.

Step 9

  • Use one hand to maintain tension in the string by grabbing the string and rotating the hand toward the fret board.
  • If tension is not retained it may result in uneven tension in the string tree, causing the tree to break.

Use one hand to maintain tension in the string by grabbing the string and rotating the hand toward the fret board.

If tension is not retained it may result in uneven tension in the string tree, causing the tree to break.

Step 10

  • Rotate the tuning peg counterclockwise until the string is slightly taut, but not tight.
  • Check to ensure that the string is lined up with the proper notch in the nut.
  • You will have proper alignment when the sting bends at a minimum angle.

Rotate the tuning peg counterclockwise until the string is slightly taut, but not tight.

Check to ensure that the string is lined up with the proper notch in the nut.

You will have proper alignment when the sting bends at a minimum angle.

Step 11

  • Repeat steps 3-10 for each string.
  • Each string will progressively get closer to the knobs. It is not essential to progress from thick to thin strings, but it is important that they are connected to the proper string tree.

Repeat steps 3-10 for each string.

Each string will progressively get closer to the knobs. It is not essential to progress from thick to thin strings, but it is important that they are connected to the proper string tree.

Step 12

  • Caution: Do not over tighten the strings. This can cause the strings to snap and could cause bodily injury. The strings are too tight when you have difficulty turning the tuning peg.
  • Tighten the string until it is close to the proper tuning. Use an electronic tuner or an online tuner that uses your computer’s microphone. (Google: Online Tuner)
  • Note: Clockwise rotation of the tuning peg tightens the string and produces a higher pitch. Counter-clockwise rotation loosens the string causing a lower pitch.
  • Tune the thickest string to B, the second thickest string E, the next thickest to A, the next string to D, and the last string to G.

Caution: Do not over tighten the strings. This can cause the strings to snap and could cause bodily injury. The strings are too tight when you have difficulty turning the tuning peg.

Tighten the string until it is close to the proper tuning. Use an electronic tuner or an online tuner that uses your computer’s microphone. (Google: Online Tuner)

Note: Clockwise rotation of the tuning peg tightens the string and produces a higher pitch. Counter-clockwise rotation loosens the string causing a lower pitch.

Tune the thickest string to B, the second thickest string E, the next thickest to A, the next string to D, and the last string to G.

Step 13

  • Because the strings will change pitch as the guitar body deforms due to increased tension, repeat step 12 after each string is tuned individually.

Because the strings will change pitch as the guitar body deforms due to increased tension, repeat step 12 after each string is tuned individually.

You have successfully replaced and tuned your strings!

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors 


                    Vincent Nguyen

Member since: 01/11/2013

79 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 5-18, Forte Winter 2013                        

                                                  Member of Cal Poly, Team 5-18, Forte Winter 2013 



                    CPSU-FORTE-W13S5G18                     


                                            4 Members                     


                                            8 Guides authored

fisheromen308 - Jan 3, 2015

Reply

Thanks for this, it’s very helpful! However, I’ve always changed strings one at a time for two reasons - 1)keeping the tension on the neck is better than relieving it all at once, and 2) it’s easier to tune the string. I usually start with the 1st string (lightest) and work my way up.