Huawei P8 Lite Vibrator Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          1 hour

Sections

Back Cover
2 steps
Loudspeaker
3 steps
Motherboard
5 steps
Vibrator
1 step

Flags

BackHuawei P8 Lite (2015)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Use an Opening Tool and start to lever up the back cover of your Huawei P8 Lite at the bottom of your phone.

Use an Opening Tool and start to lever up the back cover of your Huawei P8 Lite at the bottom of your phone.

1024

Step 2

There are clips around the whole mid frame, holding down the back cover. Open all of them with the Opening Tool.
When all clips are open, remove the back cover from the rest of the phone.
If the back cover doesn’t come freely, there are probably some additional clips that need to be disconnected.

There are clips around the whole mid frame, holding down the back cover. Open all of them with the Opening Tool.

When all clips are open, remove the back cover from the rest of the phone.

If the back cover doesn’t come freely, there are probably some additional clips that need to be disconnected.

Step 3

              Loudspeaker

Use a tweezer to remove the warranty sticker which sits on a screw in the bottom right of your phone.

Use a tweezer to remove the warranty sticker which sits on a screw in the bottom right of your phone.

Step 4

Remove the 4 black Torx T5 screws which hold down the lower part of the loudspeaker.
Remove the three silver Phillips #00 screws which hold down the upper part of the loudspeaker.

Remove the 4 black Torx T5 screws which hold down the lower part of the loudspeaker.

Remove the three silver Phillips #00 screws which hold down the upper part of the loudspeaker.

Step 5

Remove the loudspeaker carefully.

Remove the loudspeaker carefully.

Step 6

              Motherboard

Remove the three Phillips #00 screws that hold the metal plate in place.
Remove the metal plate with a tweezer.
Unplug the battery flex connector with a spudger.

Remove the three Phillips #00 screws that hold the metal plate in place.

Remove the metal plate with a tweezer.

Unplug the battery flex connector with a spudger.

Step 7

Remove the two Torx T5 screws.
If there is a tamper evident sticker over your screws remove them to properly seat your driver.
Remove the five Phillips #00 screws.

Remove the two Torx T5 screws.

If there is a tamper evident sticker over your screws remove them to properly seat your driver.

Remove the five Phillips #00 screws.

Step 8

Carefully pry off the plastic cover on the left side. The NFC antenna contacts might be slightly glued to the cover.
Then remove the top cover.

Carefully pry off the plastic cover on the left side. The NFC antenna contacts might be slightly glued to the cover.

Then remove the top cover.

Step 9

Remove the SIM card and SD card trays.
Disconnect the three plug connectors and one ZIF connector.
Unlock the ZIF connector by lifting the small black plastic lever.

Remove the SIM card and SD card trays.

Disconnect the three plug connectors and one ZIF connector.

Unlock the ZIF connector by lifting the small black plastic lever.

Step 10

Remove the volume and power button cable.
Take out the motherboard by lifting the bottom part first.
Pay attention to the cables, so they don’t rip when staying stuck to the motherboard.
On the back of the motherboard there is a thermal pad (pink rubber-like gob) for heat dissipation. If this thermal pad broke or is too dried out you might want to replace it with a new one.

Remove the volume and power button cable.

Take out the motherboard by lifting the bottom part first.

Pay attention to the cables, so they don’t rip when staying stuck to the motherboard.

On the back of the motherboard there is a thermal pad (pink rubber-like gob) for heat dissipation. If this thermal pad broke or is too dried out you might want to replace it with a new one.

Step 11

              Vibrator

Pry off the vibrator using a plastic opening tool.

Pry off the vibrator using a plastic opening tool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                    Tobias Isakeit

Member since: 03/31/2014

105,397 Reputation

                                      184 Guides authored                  



                       Badges:
                       46







                                                        +43 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

orcun adana - Nov 7, 2019

Doğrusu Güzel Anlatılmış Ve Ben Her Zaman Elektronık Tüm Parçalarda KEndi İşimi Kendım Yaparım Araba Bır Ütü Belkı Bir Mekanık Parça Bu Seferde Titreşim Motorumu Deyiştirmek İstedim Ve Bu Resimler Sayesınde Kötü tornavaıdalarla Bile yarım saatte İşlem Tamam Teşekkur Edıyorum Emegi Geçipte Burada Bunu Paylaşan Herkesten

Introduction#

What you need#

Team#

Introduction

What you need

Team