Huawei P8 Lite Display With Frame Replacement Repair Guide

Featured

Featured Guide

Difficulty

Difficult

Steps

14

Time Required

                          1 - 2 hours            

Sections

6

• Back Cover
• 2 steps
• Loudspeaker
• 3 steps
• Motherboard
• 5 steps
• Vibrator
• 1 step
• Earpiece Speaker
• 1 step
• Display with Frame
• 2 steps

Flags

1

Featured Guide

This guide has been found to be exceptionally cool by the iFixit staff.

• BackHuawei P8 Lite (2015)

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Cover               

• Use an Opening Tool and start to lever up the back cover of your Huawei P8 Lite at the bottom of your phone.

Use an Opening Tool and start to lever up the back cover of your Huawei P8 Lite at the bottom of your phone.

1024

Step 2

• There are clips around the whole mid frame, holding down the back cover. Open all of them with the Opening Tool.
• When all clips are open, remove the back cover from the rest of the phone.
• If the back cover doesn’t come freely, there are probably some additional clips that need to be disconnected.

There are clips around the whole mid frame, holding down the back cover. Open all of them with the Opening Tool.

When all clips are open, remove the back cover from the rest of the phone.

If the back cover doesn’t come freely, there are probably some additional clips that need to be disconnected.

Step 3

              Loudspeaker               

• Use a tweezer to remove the warranty sticker which sits on a screw in the bottom right of your phone.

Use a tweezer to remove the warranty sticker which sits on a screw in the bottom right of your phone.

Step 4

• Remove the 4 black Torx T5 screws which hold down the lower part of the loudspeaker.
• Remove the three silver Phillips #00 screws which hold down the upper part of the loudspeaker.

Remove the 4 black Torx T5 screws which hold down the lower part of the loudspeaker.

Remove the three silver Phillips #00 screws which hold down the upper part of the loudspeaker.

Step 5

• Remove the loudspeaker carefully.

Remove the loudspeaker carefully.

Step 6

              Motherboard               

• Remove the three Phillips #00 screws that hold the metal plate in place.
• Remove the metal plate with a tweezer.
• Unplug the battery flex connector with a spudger.

Remove the three Phillips #00 screws that hold the metal plate in place.

Remove the metal plate with a tweezer.

Unplug the battery flex connector with a spudger.

Step 7

• Remove the two Torx T5 screws.
• If there is a tamper evident sticker over your screws remove them to properly seat your driver.
• Remove the five Phillips #00 screws.

Remove the two Torx T5 screws.

If there is a tamper evident sticker over your screws remove them to properly seat your driver.

Remove the five Phillips #00 screws.

Step 8

• Carefully pry off the plastic cover on the left side. The NFC antenna contacts might be slightly glued to the cover.
• Then remove the top cover.

Carefully pry off the plastic cover on the left side. The NFC antenna contacts might be slightly glued to the cover.

Then remove the top cover.

Step 9

• Remove the SIM card and SD card trays.
• Disconnect the three plug connectors and one ZIF connector.
• Unlock the ZIF connector by lifting the small black plastic lever.

Remove the SIM card and SD card trays.

Disconnect the three plug connectors and one ZIF connector.

Unlock the ZIF connector by lifting the small black plastic lever.

Step 10

• Remove the volume and power button cable.
• Take out the motherboard by lifting the bottom part first.
• Pay attention to the cables, so they don’t rip when staying stuck to the motherboard.
• On the back of the motherboard there is a thermal pad (pink rubber-like gob) for heat dissipation. If this thermal pad broke or is too dried out you might want to replace it with a new one.

Remove the volume and power button cable.

Take out the motherboard by lifting the bottom part first.

Pay attention to the cables, so they don’t rip when staying stuck to the motherboard.

On the back of the motherboard there is a thermal pad (pink rubber-like gob) for heat dissipation. If this thermal pad broke or is too dried out you might want to replace it with a new one.

Step 11

              Vibrator               

• Pry off the vibrator using a plastic opening tool.

Pry off the vibrator using a plastic opening tool.

Step 12

              Earpiece Speaker               

• Lift out the earpiece speaker of its recess with a tweezer.
• It is glued in place with a mild adhesive, so you might need a little prying.

Lift out the earpiece speaker of its recess with a tweezer.

It is glued in place with a mild adhesive, so you might need a little prying.

Step 13

              Display with Frame               

• To avoid thermal runaway, including fire, do not bend or puncture the battery
• Use the pull tab as seen here in the battery guide to remove one of the adhesives strips underneath the battery.
• Use an opening pick or spudger to carefully pry the battery out the rest of the way.
• Never reinstall a battery that has been bent or damaged during removal.

To avoid thermal runaway, including fire, do not bend or puncture the battery

Use the pull tab as seen here in the battery guide to remove one of the adhesives strips underneath the battery.

Use an opening pick or spudger to carefully pry the battery out the rest of the way.

Never reinstall a battery that has been bent or damaged during removal.

Step 14

• Inspect your new display assembly and be sure to transfer any missing parts from the old one.

Inspect your new display assembly and be sure to transfer any missing parts from the old one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      21 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Tobias Isakeit                     

Member since: 03/31/2014

105,397 Reputation

                                      184 Guides authored                  



                       Badges:
                       46







                                                        +43 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored                     

allehoffis - Jul 9, 2018

Reply

Hat super geklappt, danke! Zwei wichtige Dinge - NFC Antenne ist schwer von Batterie zu lösen- müsste gleich bei Akku mit beschrieben sein und bei Schritt 7 oder 11, dass man noch eine Steckverbindung lösen muss (verklebt!) und übertragen muss. Hat geklappt, danke Euch - eure tools sind super dazu!

Tobias Isakeit - Jul 9, 2018

Danke allehoffis für dein Feedback. Freut mich, dass alle so weit geklappt hat. Ja, die NFC Antenne klebt da gut dran. Im separaten Akku-Guide ist darauf hingewiesen, dass sie schwer zu lösen ist. Vlt kommt hier auch noch eine Notiz dazu. In Schritt 6 wird die ZIF Verbindung getrennt. Ist es das, was du meinst mit “verklebt”?

pt5878-631 - Dec 21, 2018

Reply

Hat alles super geklappt, danke für diese Anleitung

adrian - May 2, 2020

Reply

gracias!!!!!!