Difficulty
Moderate
Steps
9
Time Required
1 hour
Sections
3
- Display
- 4 steps
- Midframe
- 3 steps
- Loudspeaker
- 2 steps
Flags
0
BackHuawei P10 Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display
- Use an iOpener to loosen the adhesive beneath the display, focusing on the upper and lower part of the display.
- Use an opening pick, or iFlex, to separate the adhesive on all sides of the display.
- To avoid damage to the display, do not push the tool too deeply into the phone.
Use an iOpener to loosen the adhesive beneath the display, focusing on the upper and lower part of the display.
Use an opening pick, or iFlex, to separate the adhesive on all sides of the display.
To avoid damage to the display, do not push the tool too deeply into the phone.
1024
Step 2
- There is a thin display cable between the screen and phone, be very careful not to rip it when opening the device.
- Place a suction cup, or iSclack, on the upper portion of the phone and lift the display off the midframe.
- Don’t remove the display, the cable is trapped under a bracket screwed to the phone. You can flip the display to lay it down without straining the cable, or simply hold it in the next steps.
There is a thin display cable between the screen and phone, be very careful not to rip it when opening the device.
Place a suction cup, or iSclack, on the upper portion of the phone and lift the display off the midframe.
Don’t remove the display, the cable is trapped under a bracket screwed to the phone. You can flip the display to lay it down without straining the cable, or simply hold it in the next steps.
Step 3
Unfasten the screw
- Remove the 3.3 mm-long Phillips screw securing the display flex connector bracket.
Remove the 3.3 mm-long Phillips screw securing the display flex connector bracket.
Step 4
- Open the metal bracket that covers the display flex cable.
- Use a spudger to disconnect the display flex cable.
- Remove the display.
- When reassembling your phone replace old adhesive with double-sided tape or pre-cut adhesive strips.
Open the metal bracket that covers the display flex cable.
Use a spudger to disconnect the display flex cable.
Remove the display.
When reassembling your phone replace old adhesive with double-sided tape or pre-cut adhesive strips.
Step 5
Midframe
- Remove the 13 Phillips #00 screws.
- Remove the metal shield which holds down the display flex connector.
Remove the 13 Phillips #00 screws.
Remove the metal shield which holds down the display flex connector.
Step 6
- Remove the SIM card tray.
- Use the pointed end of a spudger to pry out the mid frame until you can get a good grip.
Remove the SIM card tray.
Use the pointed end of a spudger to pry out the mid frame until you can get a good grip.
Step 7
- Remove the mid frame.
- Disconnect the battery flex cable with a spudger.
Remove the mid frame.
Disconnect the battery flex cable with a spudger.
Step 8
Loudspeaker
- Disconnect the loudspeaker flex cable with a spudger.
- Use an iOpener to loosen the adhesive beneath the loudspeaker.
Disconnect the loudspeaker flex cable with a spudger.
Use an iOpener to loosen the adhesive beneath the loudspeaker.
Step 9
- Only insert the spudger as deep as 1/16 of an inch to avoid damage.
- Use a spudger to carefully pry out the loudspeaker.
- Remove the loudspeaker.
Only insert the spudger as deep as 1/16 of an inch to avoid damage.
Use a spudger to carefully pry out the loudspeaker.
Remove the loudspeaker.
To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Dominik Schnabelrauch
Member since: 11/23/2016
158,135 Reputation
649 Guides authored
Badges:
40
+37 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
