Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

4

  • Back Cover
  • 3 steps
  • Battery disconnect
  • 1 step
  • Charging Board
  • 4 steps
  • Loudspeaker
  • 1 step

Flags

0

  • BackHuawei P10

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Switch off your phone.
  • Remove the two Pentalobe P2 screws at the bottom.
  • Remove the SIM card tray.

Switch off your phone.

Remove the two Pentalobe P2 screws at the bottom.

Remove the SIM card tray.

1024

Step 2

  • Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.
  • Carefully pry the display with its parts out of the case.
  • Getting the prying tool in will require some effort, be careful not to slide the tool too much or you might slightly damage the housing.
  • After you pried out the bottom end, use the opening tool to open the clamps on both sides.

Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.

Carefully pry the display with its parts out of the case.

Getting the prying tool in will require some effort, be careful not to slide the tool too much or you might slightly damage the housing.

After you pried out the bottom end, use the opening tool to open the clamps on both sides.

Step 3

  • Don’t open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.
  • Swing open the phone backwards.
  • Use a spudger to disconnect the power- and volume button flex cable.

Don’t open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.

Swing open the phone backwards.

Use a spudger to disconnect the power- and volume button flex cable.

Step 4

              Battery disconnect
  • Remove the Phillips #00 screw.
  • Use tweezers to remove the metal plate.
  • Use a spudger to disconnect the battery flex cable.

Remove the Phillips #00 screw.

Use tweezers to remove the metal plate.

Use a spudger to disconnect the battery flex cable.

Step 5

              Charging Board
  • Remove the four Phillips #00 screws.
  • Use Tweezers to remove the metal plate.

Remove the four Phillips #00 screws.

Use Tweezers to remove the metal plate.

Step 6

  • Use a spudger to disconnect the main flex cable.
  • Use tweezers to disconnect the antenna cable and pull it out of the clamp holding it down to the charging board.

Use a spudger to disconnect the main flex cable.

Use tweezers to disconnect the antenna cable and pull it out of the clamp holding it down to the charging board.

Step 7

  • Use a spudger to disconnect the headphone jack and the loudspeaker flex cables.

Use a spudger to disconnect the headphone jack and the loudspeaker flex cables.

Step 8

  • Do not damage any components sitting on the charging board while removing it.
  • Use a spudger to pry out the charging board.
  • Remove the charging board.

Do not damage any components sitting on the charging board while removing it.

Use a spudger to pry out the charging board.

Remove the charging board.

Step 9

              Loudspeaker
  • Only insert the spudger as deep as 1/16 of an inch to avoid damage.
  • Use a spudger to carefully pry out the loudspeaker. There is some adhesive underneath so it might be a little bit sticky. You can use an iOpener to loosen it.
  • Remove the loudspeaker.
  • When reassembling your phone, apply new adhesive where it’s necessary.

Only insert the spudger as deep as 1/16 of an inch to avoid damage.

Use a spudger to carefully pry out the loudspeaker. There is some adhesive underneath so it might be a little bit sticky. You can use an iOpener to loosen it.

Remove the loudspeaker.

When reassembling your phone, apply new adhesive where it’s necessary.

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors 


                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored