Difficulty
Moderate
Steps
10
Time Required
1 - 2 hours
Sections
4
- Back cover
- 4 steps
- Battery Disconnection
- 1 step
- Loudspeaker / Vibration Motor
- 3 steps
- Charging Board
- 2 steps
Flags
0
BackHuawei P10 Lite
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back cover
- Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.
- Using a suction handle to lift the back cover may help to get an initial gap for the opening pick to put in.
- If the adhesive is hard to cut, use an iOpener to loosen it.
Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.
Using a suction handle to lift the back cover may help to get an initial gap for the opening pick to put in.
If the adhesive is hard to cut, use an iOpener to loosen it.
1024
Step 2
- After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.
- Flip the rear cover over to the right side of the phone.
After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.
Flip the rear cover over to the right side of the phone.
Step 3
- Use a pair of tweezers to remove the sticker.
- Remove the two Phillips #00 screws.
- Remove the four 2.5 mm Phillips #00 screws.
Use a pair of tweezers to remove the sticker.
Remove the two Phillips #00 screws.
Remove the four 2.5 mm Phillips #00 screws.
Step 4
- Use tweezers to remove the mainboard shield.
- Use the flat end of a spudger to disconnect the finger print sensor flex cable.
- When reassembling apply new adhesive where it is necessary.
Use tweezers to remove the mainboard shield.
Use the flat end of a spudger to disconnect the finger print sensor flex cable.
When reassembling apply new adhesive where it is necessary.
Step 5
Battery Disconnection
- Remove the Phillips screw holding the battery connector plate in place.
- Remove the battery connector plate.
- Use the flat end of a spudger to disconnect the battery flex cable.
Remove the Phillips screw holding the battery connector plate in place.
Remove the battery connector plate.
Use the flat end of a spudger to disconnect the battery flex cable.
Step 6
Loudspeaker / Vibration Motor
- Remove the seven Philipps #000 screws.
Remove the seven Philipps #000 screws.
Step 7
- Insert an opening pick under the right edge of the loudspeaker unit and lever it up.
- Grab the loudspeaker unit and remove it.
Insert an opening pick under the right edge of the loudspeaker unit and lever it up.
Grab the loudspeaker unit and remove it.
Step 8
- Use an iOpener to loosen the glue under the vibration motor.
- Remove the vibration motor.
Use an iOpener to loosen the glue under the vibration motor.
Remove the vibration motor.
Step 9
Charging Board
- Use the flat end of a spudger to disconnect the interconnect cable.
- Use tweezers to disconnect the antenna cable.
Use the flat end of a spudger to disconnect the interconnect cable.
Use tweezers to disconnect the antenna cable.
Step 10
- Use an iOpener to loosen the adhesive under the charging board.
- Remove the charging board.
Use an iOpener to loosen the adhesive under the charging board.
Remove the charging board.
To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 1 other contributor
Dominik Schnabelrauch
Member since: 11/23/2016
158,135 Reputation
649 Guides authored
Badges:
40
+37 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
mj41574 - Feb 5, 2021
Reply
thanks and very nice
thanks to all team
p10 lite charging ic change daigram
