Huawei P10 Charging Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 40 minutes

Sections

Back Cover
3 steps
Battery disconnect
1 step
Charging Board
4 steps

Flags

BackHuawei P10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Switch off your phone.
Remove the two Pentalobe P2 screws at the bottom.
Remove the SIM card tray.

Switch off your phone.

Remove the two Pentalobe P2 screws at the bottom.

Remove the SIM card tray.

1024

Step 2

Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.
Carefully pry the display with its parts out of the case.
Getting the prying tool in will require some effort, be careful not to slide the tool too much or you might slightly damage the housing.
After you pried out the bottom end, use the opening tool to open the clamps on both sides.

Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.

Carefully pry the display with its parts out of the case.

Getting the prying tool in will require some effort, be careful not to slide the tool too much or you might slightly damage the housing.

After you pried out the bottom end, use the opening tool to open the clamps on both sides.

Step 3

Don’t open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.
Swing open the phone backwards.
Use a spudger to disconnect the power- and volume button flex cable.

Don’t open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.

Swing open the phone backwards.

Use a spudger to disconnect the power- and volume button flex cable.

Step 4

              Battery disconnect

Remove the Phillips #00 screw.
Use tweezers to remove the metal plate.
Use a spudger to disconnect the battery flex cable.

Remove the Phillips #00 screw.

Use tweezers to remove the metal plate.

Use a spudger to disconnect the battery flex cable.

Step 5

              Charging Board

Remove the four Phillips #00 screws.
Use Tweezers to remove the metal plate.

Remove the four Phillips #00 screws.

Use Tweezers to remove the metal plate.

Step 6

Use a spudger to disconnect the main flex cable.
Use tweezers to disconnect the antenna cable and pull it out of the clamp holding it down to the charging board.

Use a spudger to disconnect the main flex cable.

Use tweezers to disconnect the antenna cable and pull it out of the clamp holding it down to the charging board.

Step 7

Use a spudger to disconnect the headphone jack and the loudspeaker flex cables.

Use a spudger to disconnect the headphone jack and the loudspeaker flex cables.

Step 8

Do not damage any components sitting on the charging board while removing it.
Use a spudger to pry out the charging board.
Remove the charging board.

Do not damage any components sitting on the charging board while removing it.

Use a spudger to pry out the charging board.

Remove the charging board.

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Cancel: I did not complete this guide.

                                                                                      14 other people completed this guide.

Author

                                      with 5 other contributors

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

Michal Kornacki - Apr 26, 2020

Just remember to take off a tape from the microphone on a new piece. I had to open mine twice

Gerard Encina Llamas - Feb 16, 2021

If you have problems on connecting the cable to the charging port, before considering replacing the charging board, try removing the dust that may be occluding the port. Use tweezers to remove the dust and try if the cable connects. Do it carefully as your could damage the pins.

Andrew Norwood - May 1, 2021

Introduction#

What you need#

Team#

Introduction

What you need

Team