Featured

Featured Guide

Difficulty

Moderate

Steps

8

Time Required

                          1 hour

Sections

2

  • Back Cover
  • 3 steps
  • Battery
  • 5 steps

Flags

1

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackHuawei P10

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Switch off your phone.
  • Remove the two Pentalobe P2 screws at the bottom.
  • Remove the SIM card tray.

Switch off your phone.

Remove the two Pentalobe P2 screws at the bottom.

Remove the SIM card tray.

1024

Step 2

  • Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.
  • Carefully pry the display with its parts out of the case.
  • Getting the prying tool in will require some effort, be careful not to slide the tool too much or you might slightly damage the housing.
  • After you pried out the bottom end, use the opening tool to open the clamps on both sides.

Insert a plastic opening tool between the display and the case starting at the bottom area of your phone.

Carefully pry the display with its parts out of the case.

Getting the prying tool in will require some effort, be careful not to slide the tool too much or you might slightly damage the housing.

After you pried out the bottom end, use the opening tool to open the clamps on both sides.

Step 3

  • Don’t open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.
  • Swing open the phone backwards.
  • Use a spudger to disconnect the power- and volume button flex cable.

Don’t open the phone all the way, yet. The cable for the standby and volume buttons is still connected to the back cover.

Swing open the phone backwards.

Use a spudger to disconnect the power- and volume button flex cable.

Step 4

              Battery
  • Remove the two Phillips #00 screws.

Remove the two Phillips #00 screws.

Step 5

  • Use tweezers to remove the two cable brackets.

Use tweezers to remove the two cable brackets.

Step 6

  • Use a spudger to disconnect the battery, the interconnect and the display flex cable.

Use a spudger to disconnect the battery, the interconnect and the display flex cable.

Step 7

  • The battery is glued in place with two adhesive strips. One with a pull tab and one without.
  • Peel out the adhesive strip which is placed beneath the battery by steadily pulling at the tab in a flat angle.
  • It is likely that the adhesive strip rips. In this case you can grab and twist it around a tweezers tip a couple of times and then continue.
  • Use an iOpener to loosen the remaining adhesive.

The battery is glued in place with two adhesive strips. One with a pull tab and one without.

Peel out the adhesive strip which is placed beneath the battery by steadily pulling at the tab in a flat angle.

It is likely that the adhesive strip rips. In this case you can grab and twist it around a tweezers tip a couple of times and then continue.

Use an iOpener to loosen the remaining adhesive.

Step 8

  • Take care to not bend or puncture the battery.
  • Insert an opening pick or spudger beneath the battery and carefully pry it out.
  • Remove the battery.
  • When reassembling your phone, replace old adhesive with stretch release adhesive strips, double-sided tape, or pre-cut adhesive strips.
  • Never reinstall a battery that has been bent or damaged during removal.

Take care to not bend or puncture the battery.

Insert an opening pick or spudger beneath the battery and carefully pry it out.

Remove the battery.

When reassembling your phone, replace old adhesive with stretch release adhesive strips, double-sided tape, or pre-cut adhesive strips.

Never reinstall a battery that has been bent or damaged during removal.

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Cancel: I did not complete this guide.

                                                                                      70 other people completed this guide.

Author

                                      with 8 other contributors 


                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

Dave Dayanan - Feb 23, 2018

Reply

Thanks for posting this this give me new ideas.

lepisosteus74 - May 23, 2019

Reply

Facile comme bonjour. Les outils que j’avais reçu avec la batterie étaient de piètre qualité, j’ai donc utilisé des mini-spatules utilisées pour lisser les joints en silicone, c’est pile la consistance voulue pour décoller le dos et la batterie, ni trop ferme ni trop souple.

Noé Barreau - Aug 12, 2019

Reply

Easy fix, thanks a lot.

Mog Kupo - Aug 16, 2019

Reply

Excellent guide, was done in 20 minutes, thankyou!

Adriano Da Rold - Oct 9, 2019

Reply

Eccellente guida peccato che una volta montata la nuova batteria in cellulare si sente che si accende la il display rimane buio, controllato connessioni ma sono tutte ok e display sempre spento, cosa può essere?

Adriano