Huawei Mediapad S7 301U Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Battery
4 steps
Motherboard
3 steps
Screen
2 steps

Flags

BackHuawei MediaPad S7-301u
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use either your finger or a metal spudger to lift both the top and bottom black covers on the back of the tablet.

Use either your finger or a metal spudger to lift both the top and bottom black covers on the back of the tablet.

1024

Step 2

Use a Phillips (J000) bit screwdriver to remove the 6 (2 mm) screws located at the top and bottom of the tablet.

Use a Phillips (J000) bit screwdriver to remove the 6 (2 mm) screws located at the top and bottom of the tablet.

Step 3

Hold the device by the silver edge and the front of the screen.
Then use your other hand to push gently on the center back of the tablet until the front screen is detached from the silver back cover.
Finally, separate the screen from the silver back casing.

Hold the device by the silver edge and the front of the screen.

Then use your other hand to push gently on the center back of the tablet until the front screen is detached from the silver back cover.

Finally, separate the screen from the silver back casing.

Step 4

Use the plastic spudger to remove the battery from the device that is glued on the metal frame.
Be careful not to puncture the battery while removing it.
Follow the wires to where they are connected on the motherboard and simply pull the white connector out of the socket.
When removing the battery, be careful with the connector that attaches the wires to the motherboard.

Use the plastic spudger to remove the battery from the device that is glued on the metal frame.

Be careful not to puncture the battery while removing it.

Follow the wires to where they are connected on the motherboard and simply pull the white connector out of the socket.

When removing the battery, be careful with the connector that attaches the wires to the motherboard.

Step 5

              Motherboard

Once the battery is removed, the motherboard is ready to be removed.
Remove the camera from the motherboard by disconnecting the clip next to it. You can use the precision tweezer here.
To remove the power port from the motherboard, unscrew the two 4mm screws with a T5 bit.

Once the battery is removed, the motherboard is ready to be removed.

Remove the camera from the motherboard by disconnecting the clip next to it. You can use the precision tweezer here.

To remove the power port from the motherboard, unscrew the two 4mm screws with a T5 bit.

Step 6

Use the precision tweezers to disconnect the 7 clips from the motherboard
Remove the headphone input cable from the motherboard by carefully pulling on the clip.

Use the precision tweezers to disconnect the 7 clips from the motherboard

Remove the headphone input cable from the motherboard by carefully pulling on the clip.

Step 7

Unscrew the 4 screws 4mm with T5 bit from the edges or the frame of the motherboard to remove it
Carefully remove the motherboard from the metal frame.
A long thin tape will be attached to the motherboard. This tape can be pulled along with the motherboard.

Unscrew the 4 screws 4mm with T5 bit from the edges or the frame of the motherboard to remove it

Carefully remove the motherboard from the metal frame.

A long thin tape will be attached to the motherboard. This tape can be pulled along with the motherboard.

Step 8

              Screen

Remove the 7 2mm screws for on the metal frame. Use a J000 screwdriver.

Remove the 7 2mm screws for on the metal frame. Use a J000 screwdriver.

Step 9

Carefully remove the LCD from the front glass casing.
While separating the LCD from the device, be careful not to introduce any debris.

Carefully remove the LCD from the front glass casing.

While separating the LCD from the device, be careful not to introduce any debris.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors

                    Miguel Lugo

Member since: 09/26/2017

565 Reputation

                                      3 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges

Team

                       USF Tampa, Team S11-G5, Passmore Fall 2017                        

                                                  Member of USF Tampa, Team S11-G5, Passmore Fall 2017 



                    USFT-PASSMORE-F17S11G5                     


                                            4 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team