Difficulty
Moderate
Steps
7
Time Required
50 minutes
Sections
2
- Battery
- 4 steps
- Motherboard
- 3 steps
Flags
0
BackHuawei MediaPad S7-301u
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Use either your finger or a metal spudger to lift both the top and bottom black covers on the back of the tablet.
Use either your finger or a metal spudger to lift both the top and bottom black covers on the back of the tablet.
1024
Step 2
- Use a Phillips (J000) bit screwdriver to remove the 6 (2 mm) screws located at the top and bottom of the tablet.
Use a Phillips (J000) bit screwdriver to remove the 6 (2 mm) screws located at the top and bottom of the tablet.
Step 3
- Hold the device by the silver edge and the front of the screen.
- Then use your other hand to push gently on the center back of the tablet until the front screen is detached from the silver back cover.
- Finally, separate the screen from the silver back casing.
Hold the device by the silver edge and the front of the screen.
Then use your other hand to push gently on the center back of the tablet until the front screen is detached from the silver back cover.
Finally, separate the screen from the silver back casing.
Step 4
- Use the plastic spudger to remove the battery from the device that is glued on the metal frame.
- Be careful not to puncture the battery while removing it.
- Follow the wires to where they are connected on the motherboard and simply pull the white connector out of the socket.
- When removing the battery, be careful with the connector that attaches the wires to the motherboard.
Use the plastic spudger to remove the battery from the device that is glued on the metal frame.
Be careful not to puncture the battery while removing it.
Follow the wires to where they are connected on the motherboard and simply pull the white connector out of the socket.
When removing the battery, be careful with the connector that attaches the wires to the motherboard.
Step 5
Motherboard
- Once the battery is removed, the motherboard is ready to be removed.
- Remove the camera from the motherboard by disconnecting the clip next to it. You can use the precision tweezer here.
- To remove the power port from the motherboard, unscrew the two 4mm screws with a T5 bit.
Once the battery is removed, the motherboard is ready to be removed.
Remove the camera from the motherboard by disconnecting the clip next to it. You can use the precision tweezer here.
To remove the power port from the motherboard, unscrew the two 4mm screws with a T5 bit.
Step 6
- Use the precision tweezers to disconnect the 7 clips from the motherboard
- Remove the headphone input cable from the motherboard by carefully pulling on the clip.
Use the precision tweezers to disconnect the 7 clips from the motherboard
Remove the headphone input cable from the motherboard by carefully pulling on the clip.
Step 7
- Unscrew the 4 screws 4mm with T5 bit from the edges or the frame of the motherboard to remove it
- Carefully remove the motherboard from the metal frame.
- A long thin tape will be attached to the motherboard. This tape can be pulled along with the motherboard.
Unscrew the 4 screws 4mm with T5 bit from the edges or the frame of the motherboard to remove it
Carefully remove the motherboard from the metal frame.
A long thin tape will be attached to the motherboard. This tape can be pulled along with the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Miguel Lugo
Member since: 09/26/2017
565 Reputation
3 Guides authored
Badges:
19
+16 more badges
Team
USF Tampa, Team S11-G5, Passmore Fall 2017
Member of USF Tampa, Team S11-G5, Passmore Fall 2017
USFT-PASSMORE-F17S11G5
4 Members
8 Guides authored
