Difficulty
Moderate
Steps
11
Time Required
45 minutes
Sections
4
- Back Cover
- 4 steps
- Daughterboard interconnect cable
- 5 steps
- Charging Board
- 1 step
- Loudspeaker
- 1 step
Flags
0
BackHuawei Mate 8
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Switch off your phone and remove the SIM card tray.
Switch off your phone and remove the SIM card tray.
1024
Step 2
- Remove the Torx T2 screws from the bottom of the phone
Remove the Torx T2 screws from the bottom of the phone
Step 3
- Use an iSclack or a suction handle in the bottom area of your phone to separate the display unit from the rear panel.
Use an iSclack or a suction handle in the bottom area of your phone to separate the display unit from the rear panel.
Step 4
- Use an opening pick to fully separate the clips, releasing the phone.
- Do not fully remove the rear case. The fingerprint sensor cable is still connected to the back cover.
- Open the phone like a book from the SIM tray side.
- Use a spudger, to disconnect the fingerprint sensor cable.
Use an opening pick to fully separate the clips, releasing the phone.
Do not fully remove the rear case. The fingerprint sensor cable is still connected to the back cover.
Open the phone like a book from the SIM tray side.
Use a spudger, to disconnect the fingerprint sensor cable.
Step 5
Daughterboard interconnect cable
- Remove the liquid indicator sticker.
- Remove the Phillips #00 screw that holds down the metal shield.
- The metal shield is tightly held in place. If you try to remove it without holding it down on one side, it’ll break easily.
- Use a spudger to remove the metal shield.
Remove the liquid indicator sticker.
Remove the Phillips #00 screw that holds down the metal shield.
The metal shield is tightly held in place. If you try to remove it without holding it down on one side, it’ll break easily.
Use a spudger to remove the metal shield.
Step 6
- Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables.
Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables.
Step 7
- Remove the Phillips #00 screw that holds down the interconnect cable bracket.
Remove the Phillips #00 screw that holds down the interconnect cable bracket.
Step 8
- Lift the coaxial connector off of its socket to allow access to the daughterboard interconnect cable bracket.
- Remove the bracket.
Lift the coaxial connector off of its socket to allow access to the daughterboard interconnect cable bracket.
Remove the bracket.
Step 9
- Use a spudger to disconnect the interconnect cable.
- Remove the interconnect cable.
Use a spudger to disconnect the interconnect cable.
Remove the interconnect cable.
Step 10
Charging Board
- Remove the two Phillips #00 screws.
- Use the flat end a spudger to disconnect the loudspeaker flex connector.
- Use the pointy end of a spudger to pry out the daughterboard.
- Remove the daughterboard.
Remove the two Phillips #00 screws.
Use the flat end a spudger to disconnect the loudspeaker flex connector.
Use the pointy end of a spudger to pry out the daughterboard.
Remove the daughterboard.
Step 11
Loudspeaker
- Remove the two Phillips #00 screws.
- Use the tip of a spudger on the left side of the loudspeaker to pry it out.
- Remove the loudspeaker.
Use the tip of a spudger on the left side of the loudspeaker to pry it out.
Remove the loudspeaker.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Theo Mat
Member since: 11/12/2017
12,412 Reputation
14 Guides authored
Badges:
24
+21 more badges
