Huawei Mate 10 Pro Camera Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          20 minutes - 1 hour            

Sections

4

• SIM Card Tray
• 1 step
• Back Cover
• 4 steps
• Motherboard
• 5 steps
• Camera Assembly
• 1 step

Flags

1

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

• BackHuawei Mate 10 Pro

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              SIM Card Tray               

• Insert a SIM opening tool in the hole on the left side and push it in.
• Remove the SIM card tray.

Insert a SIM opening tool in the hole on the left side and push it in.

Remove the SIM card tray.

1024

Step 2

              Back Cover               

• Switch off your phone.
• Prepare an iOpener and apply it to the back of the phone for about two minutes to loosen the adhesive beneath the back cover.

Switch off your phone.

Prepare an iOpener and apply it to the back of the phone for about two minutes to loosen the adhesive beneath the back cover.

Step 3

• Lift up the back cover with a suction cup until you can insert the flat end of a halberd spudger.
• Use the halberd spudger to cut the adhesive beneath the back cover on all sides of the phone.
• Use opening picks to avoid the adhesive from sticking to the back cover again while cutting the adhesive on all sides.

Lift up the back cover with a suction cup until you can insert the flat end of a halberd spudger.

Use the halberd spudger to cut the adhesive beneath the back cover on all sides of the phone.

Use opening picks to avoid the adhesive from sticking to the back cover again while cutting the adhesive on all sides.

Step 4

• Don’t remove the back cover all the way, yet. The fingerprint sensor cable is still connected to motherboard.
• Flip the back cover over to the side.
• Remove the Phillips #00 screw which holds down the metal shield, sitting on top of the connection of the fingerprint sensor cable.

Don’t remove the back cover all the way, yet. The fingerprint sensor cable is still connected to motherboard.

Flip the back cover over to the side.

Remove the Phillips #00 screw which holds down the metal shield, sitting on top of the connection of the fingerprint sensor cable.

Step 5

• Use a pair tweezers to remove the metal shield covering the connector of the fingerprint sensor.
• Disconnect the fingerprint sensor cable with a spudger.
• When reassembling your phone apply new adhesive where it is necessary.

Use a pair tweezers to remove the metal shield covering the connector of the fingerprint sensor.

Disconnect the fingerprint sensor cable with a spudger.

When reassembling your phone apply new adhesive where it is necessary.

Step 6

              Motherboard               

• Unscrew screws on black cover and remove using tweezers to leverage.

Unscrew screws on black cover and remove using tweezers to leverage.

Step 7

• Pop off gold covers.

Pop off gold covers.

Step 8

• Disconnect wires attached to motherboard assembly.

Disconnect wires attached to motherboard assembly.

Step 9

• Wedge tweezers under motherboard and leverage assembly to pop assembly out.

Wedge tweezers under motherboard and leverage assembly to pop assembly out.

Step 10

• Separate camera assembly by popping it out, if only the motherboard is needed.

Separate camera assembly by popping it out, if only the motherboard is needed.

Step 11

              Camera Assembly               

• On the backside of the motherboard assembly, detach the camera assembly from the motherboard.

On the backside of the motherboard assembly, detach the camera assembly from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Annabelle Harding                     

Member since: 03/31/2022

433 Reputation

                                      3 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       IUPUI, Team 3-5, Harley Spring 2022                        

                                                  Member of IUPUI, Team 3-5, Harley Spring 2022 



                    IUPUI-HARLEY-S22S3G5                     


                                            3 Members                     


                                            3 Guides authored