Huawei Honor 9 Rear Glass Removal Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 25 minutes

Sections

Rear Glass
7 steps

Flags

BackHuawei Honor 9
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

You’ll need replacement adhesive to reattach components when reassembling the device.

What you need

Step 1

              Remove the Rear Glass

Switch off your phone.
Heat an iOpener and apply it to the back of the phone for around two minutes. This will help soften the adhesive securing the rear glass.
You might need to reheat and reapply the iOpener several times during the rear glass removal.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Switch off your phone.

Heat an iOpener and apply it to the back of the phone for around two minutes. This will help soften the adhesive securing the rear glass.

You might need to reheat and reapply the iOpener several times during the rear glass removal.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

1024

Step 2

Secure a suction handle to the lower edge of the rear glass, as close to the edge as possible.
If the phone’s rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.
Lift the rear glass with the suction cup to create a gap between the glass and the frame.
Insert an opening pick into the gap.
If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

Secure a suction handle to the lower edge of the rear glass, as close to the edge as possible.

If the phone’s rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

Lift the rear glass with the suction cup to create a gap between the glass and the frame.

Insert an opening pick into the gap.

If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

Step 3

Slide the opening pick to the bottom right corner.
Insert a second opening pick and slide it to the bottom left corner.
Leave the opening picks in place to prevent the adhesive from resealing.

Slide the opening pick to the bottom right corner.

Insert a second opening pick and slide it to the bottom left corner.

Leave the opening picks in place to prevent the adhesive from resealing.

Step 4

Insert a third opening pick at the bottom left corner.
Start to slide the tip of the opening pick from the bottom left corner along the side of the Huawei Honor 9 to cut the adhesive.
Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

Insert a third opening pick at the bottom left corner.

Start to slide the tip of the opening pick from the bottom left corner along the side of the Huawei Honor 9 to cut the adhesive.

Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

Step 5

If the adhesive gets hard to cut it is likely too cold. Use your iOpener to reheat it.
Insert a fourth opening pick under the top left corner of the rear glass.
Slide the opening pick along the top edge of the phone to cut the adhesive.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.

If the adhesive gets hard to cut it is likely too cold. Use your iOpener to reheat it.

Insert a fourth opening pick under the top left corner of the rear glass.

Slide the opening pick along the top edge of the phone to cut the adhesive.

Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Step 6

Insert a fifth opening pick at the top right corner of the phone.
Slide the opening pick along the right side to cut the remaining adhesive.

Insert a fifth opening pick at the top right corner of the phone.

Slide the opening pick along the right side to cut the remaining adhesive.

Step 7

Carefully lift the rear glass and remove it.
Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape.
After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

Carefully lift the rear glass and remove it.

Secure the new rear glass with pre-cut adhesive or double-sided adhesive tape.

After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

Roxane - May 12, 2020

Dante - May 17, 2021

yeah sooo

i did this in 2 minutes

without an iopener

you don’t need that

Introduction#

What you need#

Team#

Introduction

What you need

Team