Huawei Honor 6X Fingerprint Scanner Replacement Repair Guide

Difficulty

Difficult

Steps

13

Time Required

                          30 - 40 minutes            

Sections

3

• SIM Card
• 4 steps
• Back Cover
• 5 steps
• Fingerprint Scanner
• 4 steps

Flags

0

• BackHuawei Honor 6x

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              SIM Card               

• Turn off the device.

Turn off the device.

1024

Step 2

• Insert the SIM Card Eject Tool into the SIM card tray hole.
• Press the eject tool into the hole until the tray clicks open.

Insert the SIM Card Eject Tool into the SIM card tray hole.

Press the eject tool into the hole until the tray clicks open.

Step 3

• Remove the SIM tray from the device using two fingers.
• When reinserting the SIM card, be sure it is properly aligned with the SIM tray.

Remove the SIM tray from the device using two fingers.

When reinserting the SIM card, be sure it is properly aligned with the SIM tray.

Step 4

• Remove the SIM card from the compartment using two fingers.

Remove the SIM card from the compartment using two fingers.

Step 5

              Back Cover               

• Insert a plastic opening tool into the Micro USB charging port with the the angled side of the tool facing the screen.
• Pry the screen off the back of the phone by pushing down on the opening tool.

Insert a plastic opening tool into the Micro USB charging port with the the angled side of the tool facing the screen.

Pry the screen off the back of the phone by pushing down on the opening tool.

Step 6

• Slide the opening tool or spudger along the bottom of the phone and around the edge.

Slide the opening tool or spudger along the bottom of the phone and around the edge.

Step 7

• Once three sides of the screen are detached, pry the phone apart using two hands.
• When separating the back panel from the screen, do not pull them too far apart. There is an interconnect that is attached to both sides that could break, or tear, if pulled too far.

Once three sides of the screen are detached, pry the phone apart using two hands.

When separating the back panel from the screen, do not pull them too far apart. There is an interconnect that is attached to both sides that could break, or tear, if pulled too far.

Step 8

• Remove the five 4mm Phillips #00 screws using a screwdriver.

Remove the five 4mm Phillips #00 screws using a screwdriver.

Step 9

• Remove the motherboard cover from the device using a spudger or your fingers.

Remove the motherboard cover from the device using a spudger or your fingers.

Step 10

              Fingerprint Scanner               

• Disconnect the fingerprint scanner cable attached to the motherboard using a spudger or your finger.

Disconnect the fingerprint scanner cable attached to the motherboard using a spudger or your finger.

Step 11

• Apply heat around the finger print scanner assembly using a heat gun or hair dryer.

Apply heat around the finger print scanner assembly using a heat gun or hair dryer.

Step 12

• Separate the fingerprint scanner assembly from the back panel using a spudger.
• This step can be difficult. You may consider using a metal spudger.
• Be careful not to damage the black rubber adhesive around the fingerprint scanner. It is needed for water and dust resistance.

Separate the fingerprint scanner assembly from the back panel using a spudger.

This step can be difficult. You may consider using a metal spudger.

Be careful not to damage the black rubber adhesive around the fingerprint scanner. It is needed for water and dust resistance.

Step 13

• Remove the finger print scanner from the device by lifting it with two fingers.
• When reattaching the fingerprint scanner assembly, additional adhesive may be required.

Remove the finger print scanner from the device by lifting it with two fingers.

When reattaching the fingerprint scanner assembly, additional adhesive may be required.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Tessa Kemper                     

Member since: 10/08/2018

570 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       Cal Poly, Team S13-G5, White Fall 2018                        

                                                  Member of Cal Poly, Team S13-G5, White Fall 2018 



                    CPSU-WHITE-F18S13G5                     


                                            4 Members                     


                                            14 Guides authored