Huawei Honor 10 Rear Glass Removal Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Rear Glass
6 steps

Flags

BackHuawei Honor 10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

You’ll need replacement adhesive to reattach components when reassembling the device.

What you need

Step 1

              Rear Glass

Before you begin, switch off your phone.
Apply a heated iOpener to a long edge of the phone to loosen the adhesive beneath the rear glass. Apply the iOpener for at least two minutes.

Before you begin, switch off your phone.

Apply a heated iOpener to a long edge of the phone to loosen the adhesive beneath the rear glass. Apply the iOpener for at least two minutes.

1024

Step 2

If the phone’s rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.
Press a suction cup onto the back cover.
Lift the back cover’s right edge with your suction cup, opening a slight gap between the back cover and the frame.
Insert the tip of an opening pick in the gap you created and slide it to the bottom right corner.

If the phone’s rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

Press a suction cup onto the back cover.

Lift the back cover’s right edge with your suction cup, opening a slight gap between the back cover and the frame.

Insert the tip of an opening pick in the gap you created and slide it to the bottom right corner.

Step 3

Apply more heat if the adhesive becomes hard to cut. During the removal process, the back cover is under tension all the time and is likely to break if the adhesive isn’t softened enough.
Insert a second opening pick at the bottom right corner of the rear glass.
Slide the opening pick along the bottom edge of the rear glass to cut the adhesive and leave it in the bottom left corner.

Apply more heat if the adhesive becomes hard to cut. During the removal process, the back cover is under tension all the time and is likely to break if the adhesive isn’t softened enough.

Insert a second opening pick at the bottom right corner of the rear glass.

Slide the opening pick along the bottom edge of the rear glass to cut the adhesive and leave it in the bottom left corner.

Step 4

Insert a third opening pick at the bottom left corner of the rear glass.
Slide the opening pick along the left edge of the rear glass to cut the adhesive.
Leave the opening pick at the top left corner of the rear glass.

Insert a third opening pick at the bottom left corner of the rear glass.

Slide the opening pick along the left edge of the rear glass to cut the adhesive.

Leave the opening pick at the top left corner of the rear glass.

Step 5

Insert a fourth opening pick at the top left corner of the rear glass.
Slide the opening along the top edge of the rear glass and cut the remaining adhesive with it.

Insert a fourth opening pick at the top left corner of the rear glass.

Slide the opening along the top edge of the rear glass and cut the remaining adhesive with it.

Step 6

Carefully lift the rear glass of the Huawei Honor 10 and remove it.

Carefully lift the rear glass of the Huawei Honor 10 and remove it.

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

To reassemble your device, follow these instructions in reverse order.

After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team