Huawei Ascend W1 Display Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 minutes

Sections

Battery
4 steps
Antenna
5 steps
Motherboard
2 steps
Display
2 steps

Flags

BackHuawei Ascend W1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              The phone's orientation.

Flip the device over so that the back of the phone is facing you and the screen is against your palm.

Flip the device over so that the back of the phone is facing you and the screen is against your palm.

1024

Step 2

              Removing the back cover.

Locate the slit at the bottom of the back cover.
Using your fingernail, lift up on the back cover to expose the battery.

Locate the slit at the bottom of the back cover.

Using your fingernail, lift up on the back cover to expose the battery.

Step 3

Lift the back cover off the phone.
The back cover is snapped onto the phone so you will feel it unsnapping as you remove it.

Lift the back cover off the phone.

The back cover is snapped onto the phone so you will feel it unsnapping as you remove it.

Step 4

              Removing the battery.

Find the indented notch at the base of the battery.
Lift the battery out of the phone with your fingers by pressing forward and lifting upward.

Find the indented notch at the base of the battery.

Lift the battery out of the phone with your fingers by pressing forward and lifting upward.

Step 5

              Remove all the screws.

After removing the battery, remove the screws using a T6 screwdriver.
There are eleven screws that hold the middle cover to the rest of the phone.
The screw that is marked by the orange circle is covered by a white dot.

After removing the battery, remove the screws using a T6 screwdriver.

There are eleven screws that hold the middle cover to the rest of the phone.

The screw that is marked by the orange circle is covered by a white dot.

Step 6

              Removing lower section of the middle cover.

After all the screws are removed, use your fingers to remove the lower section of the middle cover.
Pull the lower section of the middle cover outward towards you, exposing the circuit board underneath.

After all the screws are removed, use your fingers to remove the lower section of the middle cover.

Pull the lower section of the middle cover outward towards you, exposing the circuit board underneath.

Step 7

              Removing the rest of the middle cover.

Begin working your way around the sides of the cover plate, unsnapping it gently.
The middle cover is a thin piece of plastic with the external speaker inside of it.
Be gentle as you remove circuit cover. The parts might break if you are too forceful.

Begin working your way around the sides of the cover plate, unsnapping it gently.

The middle cover is a thin piece of plastic with the external speaker inside of it.

Be gentle as you remove circuit cover. The parts might break if you are too forceful.

Step 8

              Locating the antenna.

The middle covers are removed.
The antenna is a thin white wire that connects to the circuit board in two locations.

The middle covers are removed.

The antenna is a thin white wire that connects to the circuit board in two locations.

Step 9

              Removing the antenna

Lift gently at each connector of the white wire to disconnect the antenna from the port.

Lift gently at each connector of the white wire to disconnect the antenna from the port.

Step 10

              Motherboard

Use a plastic spudger or your fingers to gently pry up the four flex cables from the main board.

Use a plastic spudger or your fingers to gently pry up the four flex cables from the main board.

Step 11

With the back of the phone facing you, there will be a small black clip on the left side holding the main board in place.
Gently pry up near the small black clip with your fingers or a plastic spudger to detach the main board.

With the back of the phone facing you, there will be a small black clip on the left side holding the main board in place.

Gently pry up near the small black clip with your fingers or a plastic spudger to detach the main board.

Step 12

              Display

Gently pry up near the small black clip with a plastic spudger to detach the charging board.

Gently pry up near the small black clip with a plastic spudger to detach the charging board.

Step 13

Apply heat using a heat gun or blow dryer in close proximity to the device. Then use the metal spudger to pry the display screen from the frame.

Apply heat using a heat gun or blow dryer in close proximity to the device. Then use the metal spudger to pry the display screen from the frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Tanner Cline

Member since: 11/01/2018

169 Reputation

                                      2 Guides authored                  



                       Badges:
                       2

Team

                       IUPUI, Team S3-G2, Harley Fall 2018                        

                                                  Member of IUPUI, Team S3-G2, Harley Fall 2018 



                    IUPUI-HARLEY-F18S3G2                     


                                            3 Members                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team