Difficulty
Moderate
Steps
17
Time Required
25 - 35 minutes
Sections
5
- SIM Card
- 2 steps
- Back Panel
- 2 steps
- Battery
- 7 steps
- Micro-USB Flex Cable
- 4 steps
- Motherboard
- 2 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackHuawei P6-U06
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
SIM Card
- Pull and twist the pin near the bottom left-side of the phone to remove it from the headphone jack.
Pull and twist the pin near the bottom left-side of the phone to remove it from the headphone jack.
1024
Step 2
- Insert the pin into the SIM card opening located on the right-side of the phone.
- Gently push in until the SIM card clicks, and then pull the pin and SIM card out.
- Repeat this process for the additional SIM card.
Insert the pin into the SIM card opening located on the right-side of the phone.
Gently push in until the SIM card clicks, and then pull the pin and SIM card out.
Repeat this process for the additional SIM card.
Step 3
Back Panel
- Firmly push down on the black plastic covering at the bottom of the phone, and pull down.
- You may need a sharp thin object to get underneath the plastic.
Firmly push down on the black plastic covering at the bottom of the phone, and pull down.
You may need a sharp thin object to get underneath the plastic.
Step 4
- Rotate the phone 180 degrees so that the bottom of the phone is now facing up.
- Firmly push up on the back panel with your thumbs.
- Lift up the back panel from the top right corner and gently pull it away from the phone.
Rotate the phone 180 degrees so that the bottom of the phone is now facing up.
Firmly push up on the back panel with your thumbs.
Lift up the back panel from the top right corner and gently pull it away from the phone.
Step 5
Battery
- Remove the following screws securing the logic board to the main frame:
- Five 2mm Phillips #000 screws
- Two 2.5mm Phillips #000 screws
Remove the following screws securing the logic board to the main frame:
Five 2mm Phillips #000 screws
Two 2.5mm Phillips #000 screws
Step 6
- Push down the yellow plastic lining at the top of the battery and remove the two 2.5mm Phillips #000 screws.
Push down the yellow plastic lining at the top of the battery and remove the two 2.5mm Phillips #000 screws.
Step 7
- Use the flat end of a spudger to gently snap open the first clip located on the the right arm of the retaining plate.
- Use the flat end of a spudger to gently snap the second clip located on the left arm of the retaining plate.
- Use the flat end of a spudger to gently lift the upper retaining plate from the phone.
Use the flat end of a spudger to gently snap open the first clip located on the the right arm of the retaining plate.
Use the flat end of a spudger to gently snap the second clip located on the left arm of the retaining plate.
Use the flat end of a spudger to gently lift the upper retaining plate from the phone.
Step 8
- Use the pointy end of a spudger to pry the antenna connector off of its socket.
- Upon reassembly, you will hear a “click” that indicates the pin has been properly reconnected.
Use the pointy end of a spudger to pry the antenna connector off of its socket.
Upon reassembly, you will hear a “click” that indicates the pin has been properly reconnected.
Step 9
- Use the pointy end of a spudger to gently pry the following connectors out of their sockets:
- silver LCD cable connector
- silver Headphone jack cable connector
Use the pointy end of a spudger to gently pry the following connectors out of their sockets:
silver LCD cable connector
silver Headphone jack cable connector
Step 10
- Use the pointy end of a spudger to gently pry the following connectors out of their sockets.
- Sliver Micro-USB cable connector
- Copper battery cable connector
Use the pointy end of a spudger to gently pry the following connectors out of their sockets.
Sliver Micro-USB cable connector
Copper battery cable connector
Step 11
- Be careful not to bend, puncture, or crush the battery, even if it is being replaced. The battery can potentially release toxic and flammable chemicals.
- Use a plastic opening tool to gently lift up the battery from the bottom end.
- You may need to loosen the adhesive under the battery with slow sawing motions.
Be careful not to bend, puncture, or crush the battery, even if it is being replaced. The battery can potentially release toxic and flammable chemicals.
Use a plastic opening tool to gently lift up the battery from the bottom end.
You may need to loosen the adhesive under the battery with slow sawing motions.
Step 12
Micro-USB Flex Cable
- Remove the two 2mm Phillips #000 screws securing the copper flex cable to the silver metal tab.
- The screw on the left has white paint on the top. Chipping the paint will void any warranty you have for your phone.
Remove the two 2mm Phillips #000 screws securing the copper flex cable to the silver metal tab.
The screw on the left has white paint on the top. Chipping the paint will void any warranty you have for your phone.
Step 13
- Wedge the flat end of a spudger underneath the bottom left of the metal tab.
- Run the spudger along the bottom edge of the metal tab and gently pry upward.
- Adhesive under the metal tab will make lifting the tab slightly tedious. The adhesive will come off as long as you gently run the spudger along the bottom of the tab.
Wedge the flat end of a spudger underneath the bottom left of the metal tab.
Run the spudger along the bottom edge of the metal tab and gently pry upward.
Adhesive under the metal tab will make lifting the tab slightly tedious. The adhesive will come off as long as you gently run the spudger along the bottom of the tab.
Step 14
- Gently lift the flex cable from the top-right corner.
- Do not use excessive force when removing the flex cable. Doing so may tear the cable.
Gently lift the flex cable from the top-right corner.
Do not use excessive force when removing the flex cable. Doing so may tear the cable.
Step 15
- Use tweezers to lift the rubber alignment tab out of its frame.
Use tweezers to lift the rubber alignment tab out of its frame.
Step 16
Motherboard
- Use the pointy end of a spudger to wedge underneath the black circular vibrator motor near the bottom right of the phone.
- Slowly lift up to separate the black circular vibrator motor from the adhesive.
- The vibrator motor will remain connected to the motherboard by two red and black wires.
- Be careful not to tear the red and black wires. If damaged, they will require soldering.
Use the pointy end of a spudger to wedge underneath the black circular vibrator motor near the bottom right of the phone.
Slowly lift up to separate the black circular vibrator motor from the adhesive.
The vibrator motor will remain connected to the motherboard by two red and black wires.
Be careful not to tear the red and black wires. If damaged, they will require soldering.
Step 17
- Hold down the bottom left corner of the motherboard and slowly lift the right side out of the main frame.
- Gently wiggle the logic board to release it from the phone.
Hold down the bottom left corner of the motherboard and slowly lift the right side out of the main frame.
Gently wiggle the logic board to release it from the phone.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
15 other people completed this guide.
Author
with 4 other contributors
Victor Munoz
Member since: 10/14/2014
295 Reputation
1 Guide authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 4-44, Amido Fall 2014
Member of Cal Poly, Team 4-44, Amido Fall 2014
CPSU-AMIDO-F14S4G44
5 Members
11 Guides authored
Dost Muhammad Shah - Nov 1, 2015
Reply
Hi, I need the mother board from where can I get it ??
Angel Rivas - Dec 28, 2015
Reply
Thanks Great post !!!
mm - Feb 12, 2016
Reply
emmc probleme
Jean Jumbo - Mar 25, 2016
Reply
Amigo en que parte de la placa esta el wifi y bluetooth, gracias
Friends in that part of the plate is wifi and bluetooth, thank you, have the problem that when I try to turn the wifi or bluetooth light does not help please
