Huawei Ascend P6 U06 Earpiece Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 - 35 minutes

Sections

SIM Card
2 steps
Back Panel
2 steps
Battery
7 steps
Micro-USB Flex Cable
4 steps
Earpiece Speaker
1 step

Flags

BackHuawei P6-U06
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              SIM  Card

Pull and twist the pin near the bottom left-side of the phone to remove it from the headphone jack.

Pull and twist the pin near the bottom left-side of the phone to remove it from the headphone jack.

1024

Step 2

Insert the pin into the SIM card opening located on the right-side of the phone.
Gently push in until the SIM card clicks, and then pull the pin and SIM card out.
Repeat this process for the additional SIM card.

Insert the pin into the SIM card opening located on the right-side of the phone.

Gently push in until the SIM card clicks, and then pull the pin and SIM card out.

Repeat this process for the additional SIM card.

Step 3

              Back Panel

Firmly push down on the black plastic covering at the bottom of the phone, and pull down.
You may need a sharp thin object to get underneath the plastic.

Firmly push down on the black plastic covering at the bottom of the phone, and pull down.

You may need a sharp thin object to get underneath the plastic.

Step 4

Rotate the phone 180 degrees so that the bottom of the phone is now facing up.
Firmly push up on the back panel with your thumbs.
Lift up the back panel from the top right corner and gently pull it away from the phone.

Rotate the phone 180 degrees so that the bottom of the phone is now facing up.

Firmly push up on the back panel with your thumbs.

Lift up the back panel from the top right corner and gently pull it away from the phone.

Step 5

              Battery

Remove the following screws securing the logic board to the main frame:
Five 2mm Phillips #000 screws
Two 2.5mm Phillips #000 screws

Remove the following screws securing the logic board to the main frame:

Five 2mm Phillips #000 screws

Two 2.5mm Phillips #000 screws

Step 6

Push down the yellow plastic lining at the top of the battery and remove the two 2.5mm Phillips #000 screws.

Push down the yellow plastic lining at the top of the battery and remove the two 2.5mm Phillips #000 screws.

Step 7

Use the flat end of a spudger to gently snap open the first clip located on the the right arm of the retaining plate.
Use the flat end of a spudger to gently snap the second clip located on the left arm of the retaining plate.
Use the flat end of a spudger to gently lift the upper retaining plate from the phone.

Use the flat end of a spudger to gently snap open the first clip located on the the right arm of the retaining plate.

Use the flat end of a spudger to gently snap the second clip located on the left arm of the retaining plate.

Use the flat end of a spudger to gently lift the upper retaining plate from the phone.

Step 8

Use the pointy end of a spudger to pry the antenna connector off of its socket.
Upon reassembly, you will hear a “click” that indicates the pin has been properly reconnected.

Use the pointy end of a spudger to pry the antenna connector off of its socket.

Upon reassembly, you will hear a “click” that indicates the pin has been properly reconnected.

Step 9

Use the pointy end of a spudger to gently pry the following connectors out of their sockets:
silver LCD cable connector
silver Headphone jack cable connector

Use the pointy end of a spudger to gently pry the following connectors out of their sockets:

silver LCD cable connector

silver Headphone jack cable connector

Step 10

Use the pointy end of a spudger to gently pry the following connectors out of their sockets.
Sliver Micro-USB cable connector
Copper battery cable connector

Use the pointy end of a spudger to gently pry the following connectors out of their sockets.

Sliver Micro-USB cable connector

Copper battery cable connector

Step 11

Be careful not to bend, puncture, or crush the battery, even if it is being replaced. The battery can potentially release toxic and flammable chemicals.
Use a plastic opening tool to gently lift up the battery from the bottom end.
You may need to loosen the adhesive under the battery with slow sawing motions.

Be careful not to bend, puncture, or crush the battery, even if it is being replaced. The battery can potentially release toxic and flammable chemicals.

Use a plastic opening tool to gently lift up the battery from the bottom end.

You may need to loosen the adhesive under the battery with slow sawing motions.

Step 12

              Micro-USB Flex Cable

Remove the two 2mm Phillips #000 screws securing the copper flex cable to the silver metal tab.
The screw on the left has white paint on the top. Chipping the paint will void any warranty you have for your phone.

Remove the two 2mm Phillips #000 screws securing the copper flex cable to the silver metal tab.

The screw on the left has white paint on the top. Chipping the paint will void any warranty you have for your phone.

Step 13

Wedge the flat end of a spudger underneath the bottom left of the metal tab.
Run the spudger along the bottom edge of the metal tab and gently pry upward.
Adhesive under the metal tab will make lifting the tab slightly tedious. The adhesive will come off as long as you gently run the spudger along the bottom of the tab.

Wedge the flat end of a spudger underneath the bottom left of the metal tab.

Run the spudger along the bottom edge of the metal tab and gently pry upward.

Adhesive under the metal tab will make lifting the tab slightly tedious. The adhesive will come off as long as you gently run the spudger along the bottom of the tab.

Step 14

Gently lift the flex cable from the top-right corner.
Do not use excessive force when removing the flex cable. Doing so may tear the cable.

Gently lift the flex cable from the top-right corner.

Do not use excessive force when removing the flex cable. Doing so may tear the cable.

Step 15

Use tweezers to lift the rubber alignment tab out of its frame.

Use tweezers to lift the rubber alignment tab out of its frame.

Step 16

              Earpiece Speaker

Use the pointy end of a spudger to wedge underneath the earpiece speaker, and gently pry upward.
Use tweezers to remove the earpiece speaker from the frame.
There is adhesive holding down the earpiece speaker to the frame. If the earpiece speaker is not breaking free, gently wiggle it until it comes loose.

Use the pointy end of a spudger to wedge underneath the earpiece speaker, and gently pry upward.

Use tweezers to remove the earpiece speaker from the frame.

There is adhesive holding down the earpiece speaker to the frame. If the earpiece speaker is not breaking free, gently wiggle it until it comes loose.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 5 other contributors

                    Oren Klein

Member since: 10/19/2014

391 Reputation

                                      1 Guide authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 4-44, Amido Fall 2014                        

                                                  Member of Cal Poly, Team 4-44, Amido Fall 2014 



                    CPSU-AMIDO-F14S4G44                     


                                            5 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team