Difficulty

Moderate

Steps

6

Time Required

                          10 - 30 minutes

Sections

2

  • Facerest Cushion
  • 1 step
  • Facerest
  • 5 steps

Flags

0

  • BackHTC Vive Focus

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Power down your device before you begin.

What you need

Step 1

              Remove the facerest cushion
  • Place your device upside-down on your work surface.
  • The facerest cushion is lightly held into place by seven plastic clips.
  • Use your fingers to gently pull the facerest cushion straight off of the facerest to remove it.

Place your device upside-down on your work surface.

The facerest cushion is lightly held into place by seven plastic clips.

Use your fingers to gently pull the facerest cushion straight off of the facerest to remove it.

1024

Step 2

              Remove the facerest
  • Use a T5 Torx screwdriver to remove the eight 4.5 mm screws securing the facerest.
  • One of the screws will be covered by a tamper-evident sticker. Press the driver through the sticker to remove the screw.

Use a T5 Torx screwdriver to remove the eight 4.5 mm screws securing the facerest.

One of the screws will be covered by a tamper-evident sticker. Press the driver through the sticker to remove the screw.

Step 3

  • Insert an opening pick into the upper-left corner of the facerest.
  • Twist the opening pick to release the plastic clip securing the facerest.
  • Repeat for the upper-right corner.
  • Don’t remove the facerest yet. It’s still attached by the facerest sensor ribbon cable.

Insert an opening pick into the upper-left corner of the facerest.

Twist the opening pick to release the plastic clip securing the facerest.

Repeat for the upper-right corner.

Don’t remove the facerest yet. It’s still attached by the facerest sensor ribbon cable.

Step 4

              Remove the facerest sensor
  • Carefully flip your device over.
  • Pull the facerest out just enough to access the screws securing the facerest sensor.
  • Don’t put any strain on the facerest sensor ribbon cable.
  • During reassembly, make sure the facerest sensor ribbon cable is positioned between the lenses before reinstalling the facerest.

Carefully flip your device over.

Pull the facerest out just enough to access the screws securing the facerest sensor.

Don’t put any strain on the facerest sensor ribbon cable.

During reassembly, make sure the facerest sensor ribbon cable is positioned between the lenses before reinstalling the facerest.

Step 5

  • Use a T5 Torx screwdriver to remove the two 2.4 mm screws securing the facerest sensor to the facerest.

Use a T5 Torx screwdriver to remove the two 2.4 mm screws securing the facerest sensor to the facerest.

Step 6

  • Remove the facerest.

Remove the facerest.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Sam Omiotek

Member since: 02/25/2019

55,294 Reputation

                                      288 Guides authored                  



                       Badges:
                       35







                                                        +32 more badges

Team

                       Guide Team                        

                                                  Member of Guide Team 



                    Community                     


                                            10 Members                     


                                            9,216 Guides authored