Difficulty

Moderate

Steps

10

Time Required

                          15 - 30 minutes

Sections

3

  • Battery
  • 2 steps
  • Basic Parts
  • 6 steps
  • Camera
  • 2 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackHTC Touch Pro CDMA Verizon

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Remove the back cover (not pictured) to your phone.

Remove the back cover (not pictured) to your phone.

1024

Step 2

  • To remove the battery, place your thumb beneath the tab (outlined in red here) and begin to lift.
  • Pinching the battery, lift up at an angle from the bottom of the phone.

To remove the battery, place your thumb beneath the tab (outlined in red here) and begin to lift.

Pinching the battery, lift up at an angle from the bottom of the phone.

Step 3

              Basic Parts
  • Place the battery in a container off to the side. If you do this for every step beyond this point, you will keep better track of your parts and make reassembling the device far easier when you get around to it.
  • It might not be necessary, but we recommend using an anti-static bracelet or anti-static mat from this point on. Any charge on your finger tips may cause harm to the device.

Place the battery in a container off to the side. If you do this for every step beyond this point, you will keep better track of your parts and make reassembling the device far easier when you get around to it.

It might not be necessary, but we recommend using an anti-static bracelet or anti-static mat from this point on. Any charge on your finger tips may cause harm to the device.

Step 4

  • Use a T6 screwdriver to remove the four screws on the rear plate of the HTC Touch Pro.
  • Place your screws in a bag labeled with where they came from, what screwdriver you used, and the order in which you removed them. For example, this bag would say “Rear casing. T6. #1.”

Use a T6 screwdriver to remove the four screws on the rear plate of the HTC Touch Pro.

Place your screws in a bag labeled with where they came from, what screwdriver you used, and the order in which you removed them. For example, this bag would say “Rear casing. T6. #1.”

Step 5

  • Next, remove the casing that covers the camera and motherboard.
  • To do this, place your thumbnail in any of the grooves along either side and pry it open.

Next, remove the casing that covers the camera and motherboard.

To do this, place your thumbnail in any of the grooves along either side and pry it open.

Step 6

  • Insert your spudger along the slit between the keyboard and the external casing. Pry open as shown.
  • Careful! The ribbon connecting the keyboard to the motherboard will still connect the two halves of the phone when you separate them. Be sure to take your time and move slowly to avoid damage to the cable.

Insert your spudger along the slit between the keyboard and the external casing. Pry open as shown.

Careful! The ribbon connecting the keyboard to the motherboard will still connect the two halves of the phone when you separate them. Be sure to take your time and move slowly to avoid damage to the cable.

Step 7

  • Remove the keyboard ribbon from the motherboard. To do this, simply grasp the ribbon at its base and pry it up at an angle. The ribbon has a metal end that is easily removed from the motherboard.

Remove the keyboard ribbon from the motherboard. To do this, simply grasp the ribbon at its base and pry it up at an angle. The ribbon has a metal end that is easily removed from the motherboard.

Step 8

  • Using a Phillips Head size 0 screwdriver, remove the 3 screws holding in the battery compartment.
  • Remove the ribbon covering the battery compartment by pinching it at the base and lifting.

Using a Phillips Head size 0 screwdriver, remove the 3 screws holding in the battery compartment.

Remove the ribbon covering the battery compartment by pinching it at the base and lifting.

Step 9

              Camera
  • The camera is only held in by one connection to the motherboard and some tape.
  • Remove its connection to motherboard in the same way that you’ve removed such connections in the past.

The camera is only held in by one connection to the motherboard and some tape.

Remove its connection to motherboard in the same way that you’ve removed such connections in the past.

Step 10

  • Peel the tape holding it in place.
  • After that it will be free to remove and replace as necessary.

Peel the tape holding it in place.

After that it will be free to remove and replace as necessary.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Jack Bowen

Member since: 04/09/2011

79 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 20-67, Walters Spring 2011                        

                                                  Member of Cal Poly, Team 20-67, Walters Spring 2011 



                    CPSU-WALTERS-S11S20G67                     


                                            4 Members                     


                                            10 Guides authored