Difficulty
Moderate
Steps
15
Time Required
Suggest a time??
Sections
6
- Rear Panel
- 2 steps
- Battery
- 1 step
- MicroSD Card
- 2 steps
- Rear Frame
- 5 steps
- LCD/Screen
- 4 steps
- Motherboard
- 1 step
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackHTC Thunderbolt
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Panel
- Insert the plastic opening tool into the top of the Thunderbolt near the power button.
- Gently pry up on the rear panel around the edges until it is loose.
Insert the plastic opening tool into the top of the Thunderbolt near the power button.
Gently pry up on the rear panel around the edges until it is loose.
1024
Step 2
- Lift and remove the rear panel.
Lift and remove the rear panel.
Step 3
Battery
- Using the plastic opening tool, lift up the battery from the bottom near the kickstand.
- Remove the battery from the inner frame.
Using the plastic opening tool, lift up the battery from the bottom near the kickstand.
Remove the battery from the inner frame.
Step 4
MicroSD Card
- Use your finger to push the MicroSD card in towards the top of the phone, allowing it to be released from the casing.
Use your finger to push the MicroSD card in towards the top of the phone, allowing it to be released from the casing.
Step 5
- Use tweezers to grab onto the MicroSD card and carefully remove it from the casing.
Use tweezers to grab onto the MicroSD card and carefully remove it from the casing.
Step 6
Rear Frame
- Remove the six Phillips screws from the perimeter of the rear frame.
- By removing the screw with the “void” sticker on it, your Thunderbolt will no longer be covered under warranty.
Remove the six Phillips screws from the perimeter of the rear frame.
By removing the screw with the “void” sticker on it, your Thunderbolt will no longer be covered under warranty.
Step 7
- Insert the plastic opening tool into the bottom of the phone underneath the soft keys.
- Gently pry up on the plastic cover by sliding the plastic opening tool across the bottom of the phone.
- Remove the plastic cover.
- The plastic cover will have adhesive on it making it difficult to remove.
Insert the plastic opening tool into the bottom of the phone underneath the soft keys.
Gently pry up on the plastic cover by sliding the plastic opening tool across the bottom of the phone.
Remove the plastic cover.
The plastic cover will have adhesive on it making it difficult to remove.
Step 8
- Remove the two Phillips screws where the plastic cover was.
Remove the two Phillips screws where the plastic cover was.
Step 9
- Insert the plastic opening tool in between the screen and the frame on the side of the phone.
- Slowly slide the the plastic opening tool along the side of the phone until the screen begins to separate from the frame.
- Do the same for the opposite side of the phone.
Insert the plastic opening tool in between the screen and the frame on the side of the phone.
Slowly slide the the plastic opening tool along the side of the phone until the screen begins to separate from the frame.
Do the same for the opposite side of the phone.
Step 10
- Carefully separate the screen and phone from the rear frame, starting from the bottom.
- Gently pull down on the phone and screen to fully separate it from the rear frame.
Carefully separate the screen and phone from the rear frame, starting from the bottom.
Gently pull down on the phone and screen to fully separate it from the rear frame.
Step 11
LCD/Screen
- Using the tip of an plastic opening tool flip up the tab holding the capacitive button ribbon cable.
- Be careful opening these tabs as they are very easy to break.
- Use a pair of tweezers to pull the capacitive button cable out of its socket.
Using the tip of an plastic opening tool flip up the tab holding the capacitive button ribbon cable.
Be careful opening these tabs as they are very easy to break.
Use a pair of tweezers to pull the capacitive button cable out of its socket.
Step 12
- Lifting from the side where the ribbon was disconnected, flip over the motherboard.
- Remove the black tape covering the tabs connecting the motherboard and LCD.
Lifting from the side where the ribbon was disconnected, flip over the motherboard.
Remove the black tape covering the tabs connecting the motherboard and LCD.
Step 13
- Using the plastic opening tool pop up the two tabs connecting the LCD and motherboard.
Using the plastic opening tool pop up the two tabs connecting the LCD and motherboard.
Step 14
- Once the tabs have been popped up, slowly pull the two pieces away from each other.
- If there is resistance pulling apart the phone then a ribbon or tab has not been disconnected properly/completely.
Once the tabs have been popped up, slowly pull the two pieces away from each other.
If there is resistance pulling apart the phone then a ribbon or tab has not been disconnected properly/completely.
Step 15
Motherboard
- The motherboard should now be completely disconnected
The motherboard should now be completely disconnected
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Vanessa
Member since: 01/18/2013
60 Reputation
4 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team 19-45, Regan Winter 2013
Member of Cal Poly, Team 19-45, Regan Winter 2013
CPSU-REGAN-W13S19G45
4 Members
24 Guides authored
