Difficulty
Moderate
Steps
12
Time Required
30 - 35 minutes
Sections
4
- Disassembling HTC ONE V Bottom Assembly
- 4 steps
- Disassembling HTC One V Back Case
- 3 steps
- Battery
- 2 steps
- Vibrator
- 3 steps
Flags
0
BackHTC One V
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Disassembling HTC ONE V Bottom Assembly
- Power off your device.
- Remove the bottom cover by sliding it off.
Power off your device.
Remove the bottom cover by sliding it off.
1024
Step 2
- Remove the SIM card.
- Remove the four screws securing the bottom casing.
- Two 3.0 mm Phillips #0 screws in the top left and right corners.
- Two 2.0 mm Phillips #0 screws in the bottom left and right corners.
Remove the SIM card.
Remove the four screws securing the bottom casing.
Two 3.0 mm Phillips #0 screws in the top left and right corners.
Two 2.0 mm Phillips #0 screws in the bottom left and right corners.
Step 3
- Remove the 2.0 mm Phillips #0 screws on either side of the phone.
Remove the 2.0 mm Phillips #0 screws on either side of the phone.
Step 4
- Use a plastic opening tool to pry open the bottom casing.
- Remove the bottom casing by pulling it towards you.
Use a plastic opening tool to pry open the bottom casing.
Remove the bottom casing by pulling it towards you.
Step 5
Disassembling HTC One V Back Case
- Use the plastic opening tool to pry open the rear camera panel.
- Remove both screws that are securing the back case.
- One 4.0 mm Phillips #0 screw.
- One 3.0 mm Phillips #0 screw.
Use the plastic opening tool to pry open the rear camera panel.
Remove both screws that are securing the back case.
One 4.0 mm Phillips #0 screw.
One 3.0 mm Phillips #0 screw.
Step 6
- Use a Jimmy to pry up the OEM SIM and SD card reader contact.
- Pry from right to left to avoid potential damages to the ribbon.
Use a Jimmy to pry up the OEM SIM and SD card reader contact.
Pry from right to left to avoid potential damages to the ribbon.
Step 7
- Using both thumbs, gently push on the two bottom rear corners of the motherboard.
- Gently and slowly pull the screen out from the front of the phone, while feeding the OEM reader contact through the opening.
Using both thumbs, gently push on the two bottom rear corners of the motherboard.
Gently and slowly pull the screen out from the front of the phone, while feeding the OEM reader contact through the opening.
Step 8
Battery
- Pry up the battery with the flat end of the spudger.
Pry up the battery with the flat end of the spudger.
Step 9
- Gently lift up the battery away from the edge of its housing.
- Use the point end of the spudger to push the connection out of its housing.
Gently lift up the battery away from the edge of its housing.
Use the point end of the spudger to push the connection out of its housing.
Step 10
Camera Lens
- Remove the two 3.0 mm Phillips #0 screws, that are securing the camera lens.
Remove the two 3.0 mm Phillips #0 screws, that are securing the camera lens.
Step 11
- Pry off the camera lens using a plastic opening tool.
Pry off the camera lens using a plastic opening tool.
Step 12
Vibrator
- Pry the vibrator out of the housing with a spudger.
- Using the tweezers, pull up on the connecting wires detaching the vibrator from the motherboard.
Pry the vibrator out of the housing with a spudger.
Using the tweezers, pull up on the connecting wires detaching the vibrator from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Michael Lucido
Member since: 01/20/2015
816 Reputation
6 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 1-3, Blackwell Winter 2015
Member of USF Tampa, Team 1-3, Blackwell Winter 2015
USFT-BLACKWELL-W15S1G3
4 Members
16 Guides authored
