Difficulty

Moderate

Steps

17

Time Required

                          1 hour

Sections

6

  • Disassembling HTC ONE V Bottom Assembly
  • 4 steps
  • Disassembling HTC One V Back Case
  • 3 steps
  • Battery
  • 2 steps
  • Vibrator
  • 3 steps
  • Motherboard
  • 4 steps
  • Ear Speaker
  • 1 step

Flags

0

  • BackHTC One V

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disassembling HTC ONE V Bottom Assembly
  • Power off your device.
  • Remove the bottom cover by sliding it off.

Power off your device.

Remove the bottom cover by sliding it off.

1024

Step 2

  • Remove the SIM card.
  • Remove the four screws securing the bottom casing.
  • Two 3.0 mm Phillips #0 screws in the top left and right corners.
  • Two 2.0 mm Phillips #0 screws in the bottom left and right corners.

Remove the SIM card.

Remove the four screws securing the bottom casing.

Two 3.0 mm Phillips #0 screws in the top left and right corners.

Two 2.0 mm Phillips #0 screws in the bottom left and right corners.

Step 3

  • Remove the 2.0 mm Phillips #0 screws on either side of the phone.

Remove the 2.0 mm Phillips #0 screws on either side of the phone.

Step 4

  • Use a plastic opening tool to pry open the bottom casing.
  • Remove the bottom casing by pulling it towards you.

Use a plastic opening tool to pry open the bottom casing.

Remove the bottom casing by pulling it towards you.

Step 5

              Disassembling HTC One V Back Case
  • Use the plastic opening tool to pry open the rear camera panel.
  • Remove both screws that are securing the back case.
  • One 4.0 mm Phillips #0 screw.
  • One 3.0 mm Phillips #0 screw.

Use the plastic opening tool to pry open the rear camera panel.

Remove both screws that are securing the back case.

One 4.0 mm Phillips #0 screw.

One 3.0 mm Phillips #0 screw.

Step 6

  • Use a Jimmy to pry up the OEM SIM and SD card reader contact.
  • Pry from right to left to avoid potential damages to the ribbon.

Use a Jimmy to pry up the OEM SIM and SD card reader contact.

Pry from right to left to avoid potential damages to the ribbon.

Step 7

  • Using both thumbs, gently push on the two bottom rear corners of the motherboard.
  • Gently and slowly pull the screen out from the front of the phone, while feeding the OEM reader contact through the opening.

Using both thumbs, gently push on the two bottom rear corners of the motherboard.

Gently and slowly pull the screen out from the front of the phone, while feeding the OEM reader contact through the opening.

Step 8

              Battery
  • Pry up the battery with the flat end of the spudger.

Pry up the battery with the flat end of the spudger.

Step 9

  • Gently lift up the battery away from the edge of its housing.
  • Use the point end of the spudger to push the connection out of its housing.

Gently lift up the battery away from the edge of its housing.

Use the point end of the spudger to push the connection out of its housing.

Step 10

              Camera Lens
  • Remove the two 3.0 mm Phillips #0 screws, that are securing the camera lens.

Remove the two 3.0 mm Phillips #0 screws, that are securing the camera lens.

Step 11

  • Pry off the camera lens using a plastic opening tool.

Pry off the camera lens using a plastic opening tool.

Step 12

              Vibrator
  • Pry the vibrator out of the housing with a spudger.
  • Using the tweezers, pull up on the connecting wires detaching the vibrator from the motherboard.

Pry the vibrator out of the housing with a spudger.

Using the tweezers, pull up on the connecting wires detaching the vibrator from the motherboard.

Step 13

              Motherboard
  • Using the spudger lift the tabs on the highlighted, red and orange, ribbon connectors. Gently pull out the ribbons from their connectors.
  • Remove the 3.0 mm Phillips #0 screw.

Using the spudger lift the tabs on the highlighted, red and orange, ribbon connectors. Gently pull out the ribbons from their connectors.

Remove the 3.0 mm Phillips #0 screw.

Step 14

  • Using tweezers, pull back on the tape located on the bottom corners of the motherboard.

Using tweezers, pull back on the tape located on the bottom corners of the motherboard.

Step 15

  • Use the spudger to push back the latch holding on the motherboard. While the latch is pushed back use the plastic opening tool to pry up the motherboard.

Use the spudger to push back the latch holding on the motherboard. While the latch is pushed back use the plastic opening tool to pry up the motherboard.

Step 16

  • Place your phone on its side so that you can gently pull up on the motherboard to expose its last connector.
  • Using the flat end of the spudger, pop of the connector.

Place your phone on its side so that you can gently pull up on the motherboard to expose its last connector.

Using the flat end of the spudger, pop of the connector.

Step 17

              Ear Speaker
  • Pull off the ear speaker using the tweezers.

Pull off the ear speaker using the tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Michael Lucido

Member since: 01/20/2015

816 Reputation

                                      6 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team 1-3, Blackwell Winter 2015                        

                                                  Member of USF Tampa, Team 1-3, Blackwell Winter 2015 



                    USFT-BLACKWELL-W15S1G3                     


                                            4 Members                     


                                            16 Guides authored