Difficulty
Moderate
Steps
14
Time Required
Suggest a time??
Sections
3
- Back Plate
- 5 steps
- Motherboard
- 7 steps
- Rumble Motor
- 2 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackHTC One Mini 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Sim and MicroSD Card
- Insert the end of a paper clip into the holes on each side of the phone to eject the SIM card and Micro SD card.
- Set the cardholders aside.
Insert the end of a paper clip into the holes on each side of the phone to eject the SIM card and Micro SD card.
Set the cardholders aside.
1024
Step 2
- Heat up the top grey speaker plate with the iFixit iOpener for two minutes.
Heat up the top grey speaker plate with the iFixit iOpener for two minutes.
Step 3
Front Plate
- Use a metal spudger to pry up the left edge of the upper grey front plate.
- Place the spudger between the inside white plastic edge and the grey plate. Do not pry between the two white plastic frames.
- Don’t pry against the glass. Pry against only the left side as there is a delicate antenna under the plate.
- Use the narrow plastic pry tool to carefully separate the black ribbon antenna from the grey plate.
Use a metal spudger to pry up the left edge of the upper grey front plate.
Place the spudger between the inside white plastic edge and the grey plate. Do not pry between the two white plastic frames.
Don’t pry against the glass. Pry against only the left side as there is a delicate antenna under the plate.
Use the narrow plastic pry tool to carefully separate the black ribbon antenna from the grey plate.
Step 4
- Remove the 2mm screw with a T5 torx screwdriver head from the iFixit tool kit.
Remove the 2mm screw with a T5 torx screwdriver head from the iFixit tool kit.
Step 5
- Use the plastic pry tool to pry around the edge of the phone.
- Pry carefully around the card slots.
- Slowly pull up from the right side of the screen like opening a book.
- The plastic piece for the power button may fall out. Set it aside for reassembly.
- Use the plastic spudger to peel the foam adhesive around the camera away from the back plate.
Use the plastic pry tool to pry around the edge of the phone.
Pry carefully around the card slots.
Slowly pull up from the right side of the screen like opening a book.
The plastic piece for the power button may fall out. Set it aside for reassembly.
Use the plastic spudger to peel the foam adhesive around the camera away from the back plate.
Step 6
Motherboard
- Peel off the long yellow pieces of tape on the right and left side of the copper plate.
Peel off the long yellow pieces of tape on the right and left side of the copper plate.
Step 7
- Starting from the copper plate, peel up all three woven, silver colored tapes using the spudger or narrow pry tool.
Starting from the copper plate, peel up all three woven, silver colored tapes using the spudger or narrow pry tool.
Step 8
- Using the flat end of the spudger, pop up the white tabs on all ribbon cable connectors located to the left and right of the copper plate.
- On the left side, pop the white tab up to the left. On the right, pop up to the right.
- Carefully pull out the ribbon cables.
Using the flat end of the spudger, pop up the white tabs on all ribbon cable connectors located to the left and right of the copper plate.
On the left side, pop the white tab up to the left. On the right, pop up to the right.
Carefully pull out the ribbon cables.
Step 9
- Using a Phillips #00 screwdriver, unscrew the two 1 mm screws from the bottom right corner of the motherboard that hold the power connector down.
- Pop up the battery connector using the flat end of the spudger.
Using a Phillips #00 screwdriver, unscrew the two 1 mm screws from the bottom right corner of the motherboard that hold the power connector down.
Pop up the battery connector using the flat end of the spudger.
Step 10
- Use the pointed end of the spudger to pop off the four antenna connectors. Three are located on the top left corner of the motherboard and one on the bottom right.
Use the pointed end of the spudger to pop off the four antenna connectors. Three are located on the top left corner of the motherboard and one on the bottom right.
Step 11
- Using the pointed end of the spudger, pull the wires for the rumble motor to the left to pull the connector out of the board.
- The connector is very small and easy to break so take caution when pulling it out. Wiggling the wires as you pull to the left helps.
Using the pointed end of the spudger, pull the wires for the rumble motor to the left to pull the connector out of the board.
The connector is very small and easy to break so take caution when pulling it out. Wiggling the wires as you pull to the left helps.
Step 12
- Using a T5 torx screwdriver, remove four 2mm screws from the four corners of the motherboard.
- Once the screws are removed, carefully pull the copper plated motherboard out.
Using a T5 torx screwdriver, remove four 2mm screws from the four corners of the motherboard.
Once the screws are removed, carefully pull the copper plated motherboard out.
Step 13
Rumble Motor
- Using the narrow plastic prying tool, pry up the rectangle connector covered in black foam
Using the narrow plastic prying tool, pry up the rectangle connector covered in black foam
Step 14
- Use the pointed end of the spudger to pop the rumble motor out of its housing.
Use the pointed end of the spudger to pop the rumble motor out of its housing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Jeron Hogan
Member since: 10/14/2014
818 Reputation
3 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 4-48, Amido Fall 2014
Member of Cal Poly, Team 4-48, Amido Fall 2014
CPSU-AMIDO-F14S4G48
5 Members
17 Guides authored
