Htc Droid Dna Speaker Port Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 - 45 minutes

Sections

SIM Card
2 steps
Motherboard
22 steps
Charging Port Assembly
4 steps
Speaker Port
1 step

Flags

BackHTC Droid DNA
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Remove the SIM Card Tray

Poke a paperclip into the hole to the right of the SIM Card Tray. The SIM Card Tray will automatically pop out.

Poke a paperclip into the hole to the right of the SIM Card Tray. The SIM Card Tray will automatically pop out.

1024

Step 2

              Removing the SIM Card Tray

Pull out the SIM Card Tray with your fingers.

Pull out the SIM Card Tray with your fingers.

Step 3

              Loosen the Phone Casing

Make sure the USB cover on the bottom of the phone is removed first.
Starting at a corner, slowly work your way around the edge of the sides with your prying tool to loosen the front panel.
Take your time. A lot of force is necessary to loosen the front panel.

Make sure the USB cover on the bottom of the phone is removed first.

Starting at a corner, slowly work your way around the edge of the sides with your prying tool to loosen the front panel.

Take your time. A lot of force is necessary to loosen the front panel.

Step 4

              Pull the Casing Apart

Slowly pull the panel apart from the back of the phone.
Apply a moderate force to pry the panel from the back of the phone.

Slowly pull the panel apart from the back of the phone.

Apply a moderate force to pry the panel from the back of the phone.

Step 5

              Remove the Black Tape

Set the device down so that the bottom of the phone is facing to the right.
Gently take off the piece of black tape surrounding the motherboard.
Be careful not to rip the tape.

Set the device down so that the bottom of the phone is facing to the right.

Gently take off the piece of black tape surrounding the motherboard.

Be careful not to rip the tape.

Step 6

              Remove the Yellow Tape

Use your tweezers to take off the yellow tape on the bottom left corner of the phone.

Use your tweezers to take off the yellow tape on the bottom left corner of the phone.

Step 7

Rotate your phone 90 degrees clockwise so the bottom of the phone is facing you.
Use the T5 Torx screwdriver to remove the two 4mm screws located at the bottom of the phone.

Rotate your phone 90 degrees clockwise so the bottom of the phone is facing you.

Use the T5 Torx screwdriver to remove the two 4mm screws located at the bottom of the phone.

Step 8

              Remove the Void Screw

Use the Phillips #000 screwdriver to remove the single 2.7mm void screw on the bottom right.

Use the Phillips #000 screwdriver to remove the single 2.7mm void screw on the bottom right.

Step 9

              Remove the Screw Retaining Bracket

Rotate your phone back 90 Degrees counter-clockwise.
Use your tweezers to take off the small metal retaining bracket on the bottom right of the phone.

Rotate your phone back 90 Degrees counter-clockwise.

Use your tweezers to take off the small metal retaining bracket on the bottom right of the phone.

Step 10

              Remove the Connector Screws

Remove the following Phillips #000 screws from the motherboard:
Four 1.6 mm screws
Two 1.5 mm screws

Remove the following Phillips #000 screws from the motherboard:

Four 1.6 mm screws

Two 1.5 mm screws

Step 11

              Unfasten the Connectors

Use your pry tool to unfasten the connectors on both sides of the motherboard.
The connectors will still be attached to the green camera board at the top so DO NOT try to pull them off or bend them severely.

Use your pry tool to unfasten the connectors on both sides of the motherboard.

The connectors will still be attached to the green camera board at the top so DO NOT try to pull them off or bend them severely.

Step 12

              Remove the Yellow Tape

Use your tweezers to remove the two pieces of yellow tape shown.

Use your tweezers to remove the two pieces of yellow tape shown.

Step 13

              Flipping up the White Board

Use your tweezers to gently snap up the white board on the bottom right of the motherboard.

Use your tweezers to gently snap up the white board on the bottom right of the motherboard.

Step 14

              Disconnect the Connector

Use your tweezers to disconnect the black connector on the bottom right of the motherboard.
Be careful not to bend the Flex Cable of the Connector.

Use your tweezers to disconnect the black connector on the bottom right of the motherboard.

Be careful not to bend the Flex Cable of the Connector.

Step 15

              Flipping up the White Board

Use your tweezers to gently snap the other white board on the bottom right of the motherboard up.

Use your tweezers to gently snap the other white board on the bottom right of the motherboard up.

Step 16

              Disconnect the Connector

Use your tweezers to disconnect the other small connector on the bottom right of the motherboard.
Be careful not to bend the Flex Cables for the Connector.

Use your tweezers to disconnect the other small connector on the bottom right of the motherboard.

Be careful not to bend the Flex Cables for the Connector.

Step 17

              Flipping up the White Board

Rotate the phone 180 degrees.
Use your tweezers to gently snap up the white board on the top left of the motherboard.

Rotate the phone 180 degrees.

Use your tweezers to gently snap up the white board on the top left of the motherboard.

Step 18

              Disconnect the Connector

Use your tweezers to disconnect the cable on the top left of the motherboard.
Be careful not to bend the Flex Cable of the Connector.

Use your tweezers to disconnect the cable on the top left of the motherboard.

Step 19

              Flipping up the Black Board

Use your tweezers to gently snap up the black board on the top left of the motherboard.

Use your tweezers to gently snap up the black board on the top left of the motherboard.

Step 20

              Disconnect the Small Ribbon Connector

Use your tweezers to gently remove the yellow connector on the top left of the phone.

Use your tweezers to gently remove the yellow connector on the top left of the phone.

Step 21

              Remove the Black Wire

Remove the long black wire on the left of the motherboard.

Remove the long black wire on the left of the motherboard.

Step 22

              Remove the Two Black Wires

Reorient the phone so that the green camera board is farthest from you.
Use your tweezers to remove the two wires located at the top of the board. The wires snap off very easily so not much force is needed.

Reorient the phone so that the green camera board is farthest from you.

Use your tweezers to remove the two wires located at the top of the board. The wires snap off very easily so not much force is needed.

Step 23

              Remove the Screws

Use a Phillips #000 screwdriver to remove the two 3.9mm screws on top of motherboard.

Use a Phillips #000 screwdriver to remove the two 3.9mm screws on top of motherboard.

Step 24

              Remove the Motherboard

Now, use your fingers to slowly pull up the motherboard and remove it from the phone.

Now, use your fingers to slowly pull up the motherboard and remove it from the phone.

Step 25

              Remove the Charging Port Assembly

Use the plastic prying tool to gently remove the charging port assembly.

Use the plastic prying tool to gently remove the charging port assembly.

Step 26

              Disassemble Charging Port Assembly

Use a Phillips #000 screw driver to remove the single 2.1mm screw located on the backside of the assembly.

Use a Phillips #000 screw driver to remove the single 2.1mm screw located on the backside of the assembly.

Step 27

              Undo the Wire Connection

Use your tweezers to undo the red and black wire connection.

Use your tweezers to undo the red and black wire connection.

Step 28

              Separate the Black and Blue Assembly Pieces

Use the plastic prying tool to separate the assembly into two pieces: blue and black.

Use the plastic prying tool to separate the assembly into two pieces: blue and black.

Step 29

              Removing the speaker

Apply pressure to the grey side of the speaker with a blunt object to push out the speaker.
The speaker is stuck with adhesive so it will take a little bit of extra force.

Apply pressure to the grey side of the speaker with a blunt object to push out the speaker.

The speaker is stuck with adhesive so it will take a little bit of extra force.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Sam Gallagher

Member since: 10/14/2014

113 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Cal Poly, Team 4-43, Amido Fall 2014                        

                                                  Member of Cal Poly, Team 4-43, Amido Fall 2014 



                    CPSU-AMIDO-F14S4G43                     


                                            4 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team