Difficulty
Moderate
Steps
19
Time Required
30 - 35 minutes
Sections
6
- Battery
- 2 steps
- Midframe
- 2 steps
- Button Assembly
- 3 steps
- Vibration Motor
- 2 steps
- Motherboard Assembly
- 8 steps
- Earpiece Speaker
- 2 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackHTC Desire V
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Gently pry back cover away from phone.
- If you are having difficulty you may need to use a Spudger or plastic opener.
Gently pry back cover away from phone.
If you are having difficulty you may need to use a Spudger or plastic opener.
1024
Step 2
- Lever the battery out from the bottom end first.
- Do not bend or puncture the battery.
Lever the battery out from the bottom end first.
Do not bend or puncture the battery.
Step 3
Midframe
- Use a Torx T5 screwdriver to unscrew and remove five 3.0 mm screws from the rear frame.
Use a Torx T5 screwdriver to unscrew and remove five 3.0 mm screws from the rear frame.
Step 4
- Use an opening tool or a spudger to gently remove the rear frame.
Use an opening tool or a spudger to gently remove the rear frame.
Step 5
Button Assembly
- Remove the connector on left side of the Navigation board by unplugging/prying the orange ribbon.
Remove the connector on left side of the Navigation board by unplugging/prying the orange ribbon.
Step 6
- Gently unplug and remove aerial cable (black antenna) from bottom plug.
Gently unplug and remove aerial cable (black antenna) from bottom plug.
Step 7
- Nav Board will be stuck down by glue.
- Pull gently from the right end of the board, being careful of its flexibility.
Nav Board will be stuck down by glue.
Pull gently from the right end of the board, being careful of its flexibility.
Step 8
Vibration Motor
- Unplug the vibration motor shown from the white plug on the motherboard.
- You will probably need tweezers to do this.
Unplug the vibration motor shown from the white plug on the motherboard.
You will probably need tweezers to do this.
Step 9
- Gently remove the motor from its housing in the phone’s chassis.
- The easiest way to do this is to lever the motor out by its rotating end using the tweezers.
Gently remove the motor from its housing in the phone’s chassis.
The easiest way to do this is to lever the motor out by its rotating end using the tweezers.
Step 10
Motherboard Assembly
- Remove the black information sticker if this is the first time opening the handset.
Remove the black information sticker if this is the first time opening the handset.
Step 11
- You should now see a black ribbon cable, which was connected at the left to the Nav board, and on the right, to a gold ribbon cable which goes to the screen.
- Unlock the gold ribbon cable connecting screen to logic board by lifting the locking tab at the back of the socket.
- For this you may wish to use a spudger or tweezers.
You should now see a black ribbon cable, which was connected at the left to the Nav board, and on the right, to a gold ribbon cable which goes to the screen.
Unlock the gold ribbon cable connecting screen to logic board by lifting the locking tab at the back of the socket.
For this you may wish to use a spudger or tweezers.
Step 12
- Disconnect gold ribbon cable connecting screen to logic board by pulling cable out gently.
Disconnect gold ribbon cable connecting screen to logic board by pulling cable out gently.
Step 13
- Gently unstick black ribbon cable from the chassis.
Gently unstick black ribbon cable from the chassis.
Step 14
- Unscrew the 2mm silver screw from top left.
- Use a Phillips PH00 Screwdriver for this.
Unscrew the 2mm silver screw from top left.
Use a Phillips PH00 Screwdriver for this.
Step 15
- Gently pry logic board from the casing by lifting the left side up, as if there was a hinge on the right, folding it over the right edge where you will see a gold/orange ribbon cable.
Gently pry logic board from the casing by lifting the left side up, as if there was a hinge on the right, folding it over the right edge where you will see a gold/orange ribbon cable.
Step 16
- Remove the gold ribbon cable by lifting tab at the back of the socket, using a spudger or tweezers.
Remove the gold ribbon cable by lifting tab at the back of the socket, using a spudger or tweezers.
Step 17
- Gently pull the logic board to the right and it will disconnect from the chassis.
Gently pull the logic board to the right and it will disconnect from the chassis.
Step 18
Earpiece Speaker
- At the top of the phone is the speaker, with two gold coloured connectors.
- At the right hand side there is a space where using the fine tweezers you can gently pry the speaker from it’s housing.
At the top of the phone is the speaker, with two gold coloured connectors.
At the right hand side there is a space where using the fine tweezers you can gently pry the speaker from it’s housing.
Step 19
- Make sure you don’t lose the speaker, as it is very small and can stick to metal objects.
Make sure you don’t lose the speaker, as it is very small and can stick to metal objects.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
William McCusker
Member since: 01/29/2015
1,096 Reputation
9 Guides authored
Badges:
12
+9 more badges
Team
Clemson, Team 14-3, Shirley Winter 2015
Member of Clemson, Team 14-3, Shirley Winter 2015
CLEM-SHIRLEY-W15S14G3
6 Members
18 Guides authored
