Difficulty

Moderate

Steps

8

Time Required

                          5 minutes

Sections

2

  • Battery
  • 4 steps
  • Headphone Jack
  • 4 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHTC Desire 826

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Find a seam in the back of the device.
  • Insert the plastic spudger into the seam and pry off the back panel.
  • There will be glue, so keep prying until it comes off or you may need to heat up the edges of the device to loosen the adhesive with the iOpener.

Find a seam in the back of the device.

Insert the plastic spudger into the seam and pry off the back panel.

There will be glue, so keep prying until it comes off or you may need to heat up the edges of the device to loosen the adhesive with the iOpener.

1024

Step 2

  • Remove the 4.0 mm screw above the battery with a T5 Torx screwdriver.
  • Remove the metal bracket with the tweezers.

Remove the 4.0 mm screw above the battery with a T5 Torx screwdriver.

Remove the metal bracket with the tweezers.

Step 3

  • Disconnect the battery cable from the motherboard with the tweezers.

Disconnect the battery cable from the motherboard with the tweezers.

Step 4

  • Lift the battery with a plastic spudger and remove it from the device.

Lift the battery with a plastic spudger and remove it from the device.

Step 5

              Headphone Jack
  • Use the T5 screwdriver to remove the three 4.00 mm screws as shown.
  • Once the screws are removed, pry up the top plastic panel using the black nylon spudger.

Use the T5 screwdriver to remove the three 4.00 mm screws as shown.

Once the screws are removed, pry up the top plastic panel using the black nylon spudger.

Step 6

  • Unscrew the two 4.00 mm screws attaching the bottom plastic panel using a T5 screwdriver.
  • Using the spudger, remove the bottom plastic piece.

Unscrew the two 4.00 mm screws attaching the bottom plastic panel using a T5 screwdriver.

Using the spudger, remove the bottom plastic piece.

Step 7

  • Using the spudger, remove the bottom part of the motherboard.
  • Using the angled tweezers, disconnect the headphone jack from the motherboard.
  • Using the plastic spudger, pop out the circular silver piece and lift the top part of the motherboard.

Using the spudger, remove the bottom part of the motherboard.

Using the angled tweezers, disconnect the headphone jack from the motherboard.

Using the plastic spudger, pop out the circular silver piece and lift the top part of the motherboard.

Step 8

  • Using the angled tweezers, pop off the metal piece on top of the headphone jack.
  • Using the angled tweezers, remove the headphone jack.

Using the angled tweezers, pop off the metal piece on top of the headphone jack.

Using the angled tweezers, remove the headphone jack.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Payton Rawson

Member since: 09/04/2019

109 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       University of Alabama, Team S1-G2, Bedsole Fall 2019                        

                                                  Member of University of Alabama, Team S1-G2, Bedsole Fall 2019 



                    UA-BEDSOLE-F19S1G2                     


                                            4 Members                     


                                            10 Guides authored