Difficulty

Very easy

Steps

10

Time Required

                          15 minutes

Sections

4

  • Battery
  • 2 steps
  • Rear Panel
  • 2 steps
  • Motherboard
  • 5 steps
  • Rear Facing Camera
  • 1 step

Flags

1

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackHTC Desire 700 Dual Sim

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Use the spudger to pry the back cover off.

Use the spudger to pry the back cover off.

1024

Step 2

              Removing Battery
  • Use spudger tool to pry under the battery to lift it up and out.

Use spudger tool to pry under the battery to lift it up and out.

Step 3

              Remove 8 Torx Screws
  • Remove eight 8.3mm T4 screws with the Torx screwdriver.

Remove eight 8.3mm T4 screws with the Torx screwdriver.

Step 4

              Prying Off Rear Panel
  • Pry the back panel of the screen using the plastic opener.
  • Work your way gently around the device, using picks as necessary to keep the back panel separated.
  • Use caution not to damage the device, as it takes force to remove the rear panel.

Pry the back panel of the screen using the plastic opener.

Work your way gently around the device, using picks as necessary to keep the back panel separated.

Use caution not to damage the device, as it takes force to remove the rear panel.

Step 5

              Motherboard
  • Remove the 3mm PH00 screw located at the bottom center of the motherboard using a P#00 Phillip’s head screwdriver.

Remove the 3mm PH00 screw located at the bottom center of the motherboard using a P#00 Phillip’s head screwdriver.

Step 6

              Disconnect Vibrator Wire
  • Using the tweezers gently disconnect the wire from the vibrator located on the motherboard.

Using the tweezers gently disconnect the wire from the vibrator located on the motherboard.

Step 7

  • Remove volume control button ribbon with tweezers.

Remove volume control button ribbon with tweezers.

Step 8

  • Carefully remove the ribbon attached to the top of the motherboard.

Carefully remove the ribbon attached to the top of the motherboard.

Step 9

  • Unsnap the wire from the printed circuit board (PCB) using the tweezers.

Unsnap the wire from the printed circuit board (PCB) using the tweezers.

Step 10

              Remove Rear Facing Camera
  • Carefully remove the ribbon that attaches the camera to the front screen using the tweezers and the plastic opening tool.

Carefully remove the ribbon that attaches the camera to the front screen using the tweezers and the plastic opening tool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Steven Pate

Member since: 09/23/2014

191 Reputation

                                      7 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 9-3, Blackwell Fall 2014                        

                                                  Member of USF Tampa, Team 9-3, Blackwell Fall 2014 



                    USFT-BLACKWELL-F14S9G3                     


                                            4 Members                     


                                            14 Guides authored

stboscoojo - May 26, 2016

Reply

my screen conector on the motherbord got damaged what can i do about it?

Aissa Brahimi - Oct 8, 2017

Reply

On step 10, what is that big copper cover? Is it an LNA shield? What is the right tool to remove it?

Thank for this tutorial