Difficulty
Difficult
Steps
8
Time Required
30 - 45 minutes
Sections
2
- Battery
- 4 steps
- Speaker
- 4 steps
Flags
0
BackHTC Desire 530
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Use the plastic opening tools to remove the plastic speaker covers that are attached through an adhesive layer.
- They may be difficult to peel off and you might want to consider loosening the adhesive layer by running a hair dryer or a heat gun over it briefly to allow them to peel off easily.
Use the plastic opening tools to remove the plastic speaker covers that are attached through an adhesive layer.
They may be difficult to peel off and you might want to consider loosening the adhesive layer by running a hair dryer or a heat gun over it briefly to allow them to peel off easily.
1024
Step 2
- Use the T5 Torx screwdriver to remove the four screws in each corner.
- Make sure to take out any SD cards, located on the left side of the phone before proceeding to the next step.
- Use the plastic opening tool to pry the front of the device off. Fully go around the front with the plastic opening tool before attempting to pull it off.
Use the T5 Torx screwdriver to remove the four screws in each corner.
Make sure to take out any SD cards, located on the left side of the phone before proceeding to the next step.
Use the plastic opening tool to pry the front of the device off. Fully go around the front with the plastic opening tool before attempting to pull it off.
Step 3
- Dislocate the small piece with the wires connected using a nylon spudger.
- Loosen the adhesive layer for the battery by running a hair dryer over it briefly. After the adhesive is loosened you can pry the battery out with a plastic opening tool.
Dislocate the small piece with the wires connected using a nylon spudger.
Loosen the adhesive layer for the battery by running a hair dryer over it briefly. After the adhesive is loosened you can pry the battery out with a plastic opening tool.
Step 4
- After prying, simply lift the battery up and out of the device.
After prying, simply lift the battery up and out of the device.
Step 5
Speaker
- Use the T5 Torx screwdriver to remove the screw located on the left side.
- Use the spudger to slowly pry off the black cover.
- Slowly pry off the circuit board with the spudger in a very cautious manner.
Use the T5 Torx screwdriver to remove the screw located on the left side.
Use the spudger to slowly pry off the black cover.
Slowly pry off the circuit board with the spudger in a very cautious manner.
Step 6
- Remove the rubber object by pinching and pulling it out.
- Take the speaker out of the holder.
Remove the rubber object by pinching and pulling it out.
Take the speaker out of the holder.
Step 7
- To access the top speaker, you must first detach the orange cable from its holder with your fingers.
- Remove the T5 Torx screw.
- Carefully pry off the circular object with the spudger.
- Do not accidentally disconnect this object from the phone. It is connected by 2 short wires.
To access the top speaker, you must first detach the orange cable from its holder with your fingers.
Remove the T5 Torx screw.
Carefully pry off the circular object with the spudger.
Do not accidentally disconnect this object from the phone. It is connected by 2 short wires.
Step 8
- Use the spudger to carefully work your way around the edge of the motherboard and slowly pry it off.
- Use the spudger to pry off the speaker.
Use the spudger to carefully work your way around the edge of the motherboard and slowly pry it off.
Use the spudger to pry off the speaker.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Thomas Morin
Member since: 10/25/2018
241 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
UMASSD-PEAK-F18S3G2
Member of UMASSD-PEAK-F18S3G2
Community
3 Members
10 Guides authored
