Htc Desire 530 Screen Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 - 45 minutes

Sections

Battery
4 steps
Screen
5 steps

Flags

BackHTC Desire 530
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use the plastic opening tools to remove the plastic speaker covers that are attached through an adhesive layer.
They may be difficult to peel off and you might want to consider loosening the adhesive layer by running a hair dryer or a heat gun over it briefly to allow them to peel off easily.

Use the plastic opening tools to remove the plastic speaker covers that are attached through an adhesive layer.

They may be difficult to peel off and you might want to consider loosening the adhesive layer by running a hair dryer or a heat gun over it briefly to allow them to peel off easily.

1024

Step 2

Use the T5 Torx screwdriver to remove the four screws in each corner.
Make sure to take out any SD cards, located on the left side of the phone before proceeding to the next step.
Use the plastic opening tool to pry the front of the device off. Fully go around the front with the plastic opening tool before attempting to pull it off.

Use the T5 Torx screwdriver to remove the four screws in each corner.

Make sure to take out any SD cards, located on the left side of the phone before proceeding to the next step.

Use the plastic opening tool to pry the front of the device off. Fully go around the front with the plastic opening tool before attempting to pull it off.

Step 3

Dislocate the small piece with the wires connected using a nylon spudger.
Loosen the adhesive layer for the battery by running a hair dryer over it briefly. After the adhesive is loosened you can pry the battery out with a plastic opening tool.

Dislocate the small piece with the wires connected using a nylon spudger.

Loosen the adhesive layer for the battery by running a hair dryer over it briefly. After the adhesive is loosened you can pry the battery out with a plastic opening tool.

Step 4

After prying, simply lift the battery up and out of the device.

After prying, simply lift the battery up and out of the device.

Step 5

              Screen

After the battery has been removed, there are two screws that also need to be removed
There are two gold strips that you must disconnect from the motherboard, They simply pop right off.

After the battery has been removed, there are two screws that also need to be removed

There are two gold strips that you must disconnect from the motherboard, They simply pop right off.

Step 6

Remove the circular piece from the motherboard.
Proceed to pry off the motherboard. Go around all edges with the plastic opening tool and it should come off with ease.

Remove the circular piece from the motherboard.

Proceed to pry off the motherboard. Go around all edges with the plastic opening tool and it should come off with ease.

Step 7

Next, the motherboard should still be connected by a wire that leads to the bottom portion of the phone.
To remove the black plastic piece there is one screw that needs to be removed then you can pry it off with the plastic opening tool.

Next, the motherboard should still be connected by a wire that leads to the bottom portion of the phone.

To remove the black plastic piece there is one screw that needs to be removed then you can pry it off with the plastic opening tool.

Step 8

To fully remove the motherboard the last step is to disconnect the wire that was previously mentioned.
Remove the motherboard.
Removal of wire from daughterboard is optional.

To fully remove the motherboard the last step is to disconnect the wire that was previously mentioned.

Remove the motherboard.

Removal of wire from daughterboard is optional.

Step 9

After the phone is gutted, all that is left is to pry the actual screen off from the backing and prepare for replacement.

After the phone is gutted, all that is left is to pry the actual screen off from the backing and prepare for replacement.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors

                    Thomas Morin

Member since: 10/25/2018

241 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UMASSD-PEAK-F18S3G2                        

                                                  Member of UMASSD-PEAK-F18S3G2 



                    Community                     


                                            3 Members                     


                                            10 Guides authored

Mark Bourne - Jan 18, 2021

Excellent… thank you

Introduction#

What you need#

Team#

Introduction

What you need

Team