Htc Desire 510 Touch Screen Glass And Or Lcd Display Repair Guide

Difficulty

Difficult

Steps

10

Time Required

                          25 - 30 minutes            

Sections

3

• Loudspeaker (Ringer)
• 2 steps
• Logic Board
• 2 steps
• Touch screen Glass and/or LCD Display
• 6 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackHTC Desire 510

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Video Overview

Step 1

              BATTERY REMOVAL               

• Switch off the phone, remove the battery and any installed SIM and memory cards.
• Remove 7x Torx T5 screws.

Switch off the phone, remove the battery and any installed SIM and memory cards.

Remove 7x Torx T5 screws.

1024

Step 2

              REAR BEZEL REMOVAL               

• Use a plastic tool to remove the rear bezel.
• The loudspeaker is on the inner side of the rear bezel.

Use a plastic tool to remove the rear bezel.

The loudspeaker is on the inner side of the rear bezel.

Step 3

              FLEX CABLES DISCONNECTING               

• Disconnect the touch screen flex cable.
• Disconnect the light sensor flex cable.
• Unstuck the vibra-motor from the middle frame.
• Remove the coaxial antenna cable from the middle frame.
• The LCD display flex cable is connected to the bottom side of the board.

Disconnect the touch screen flex cable.

Disconnect the light sensor flex cable.

Unstuck the vibra-motor from the middle frame.

Remove the coaxial antenna cable from the middle frame.

The LCD display flex cable is connected to the bottom side of the board.

Step 4

              LOGIC BOARD REMOVAL               

• At the upper left side, the board is held by a plastic locking clip. Use a plastic tool and start the separating from here.
• Gently disconnect the LCD display flex cable.
• Now remove the logic board.

At the upper left side, the board is held by a plastic locking clip. Use a plastic tool and start the separating from here.

Gently disconnect the LCD display flex cable.

Now remove the logic board.

Step 5

              PREPARATION THE GLASS               

• Put a scotch tape to prevent the glass from scattering.
• Use a hot gun or hair dryer and warm the glass. This will make the adhesive soften and the separation easier.

Put a scotch tape to prevent the glass from scattering.

Use a hot gun or hair dryer and warm the glass. This will make the adhesive soften and the separation easier.

Step 6

              SEPARATION THE GLASS               

• Use a cutter and slightly lift the glass in one of the corners. When you make enough room, put a plastic tool.
• Continue the separating with plastic tools to prevent the middle frame from scratches.

Use a cutter and slightly lift the glass in one of the corners. When you make enough room, put a plastic tool.

Continue the separating with plastic tools to prevent the middle frame from scratches.

Step 7

              SEPARATION THE GLASS (2)               

• The digitizer flex cable goes under the LCD display.
• Slightly lift the display and unstuck the digitizer ribbon cable from the from the rear side of the display.

The digitizer flex cable goes under the LCD display.

Slightly lift the display and unstuck the digitizer ribbon cable from the from the rear side of the display.

Step 8

              LCD DISPLAY               

• If you have a broken LCD display, use a plastic tool and remove it from the middle frame.
• It’s not glued to the frame.

If you have a broken LCD display, use a plastic tool and remove it from the middle frame.

It’s not glued to the frame.

Step 9

              INSTALLING THE NEW SPARE PART               

• Install a new adhesive tape on the digitizer glass.
• First put the touch screen flex cable in the right hole and then install the LCD Display.

Install a new adhesive tape on the digitizer glass.

First put the touch screen flex cable in the right hole and then install the LCD Display.

Step 10

              REASSEMBLING               

• Now is time to reassemble the phone.
• That’s all.
• .
• .
• .
• .
• Did you do it successfully?

Now is time to reassemble the phone.

That’s all.

.

Did you do it successfully?

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.                                             

Author

                    ZFix                     

Member since: 12/09/2013

187,195 Reputation

                                      330 Guides authored                  



                       Badges:
                       35





                                                        +32 more badges                           

Team

                       Master Techs                        

                                                  Member of Master Techs 



                    Community                     


                                            310 Members                     


                                            1,168 Guides authored                     

kommer - Jul 1, 2016

Reply

thanks for this mate, super helpful

Generic Email - Jul 15, 2016

Reply

I did exactly this and when I turn on my phone, the digitizer recognizes touches for a few milliseconds (buggy touches) when I touch it then it stops recognizing touches. What did I do wrong?

imran Ali Gaming - Nov 21, 2019

Reply

hello i want to buy HTC desire 510 Screen because my htc mobile Touch is not working. i want to buy. plz tell me to am i buy .