Difficulty
Easy
Steps
6
Time Required
5 - 10 minutes
Sections
2
- Battery
- 1 step
- Screen
- 5 steps
Flags
0
BackHP ZBook 15
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Flip the laptop over.
- Slide the lever with the battery symbol beside it firmly until the battery pops out.
- Remove the battery from the laptop.
Flip the laptop over.
Slide the lever with the battery symbol beside it firmly until the battery pops out.
Remove the battery from the laptop.
1024
Step 2
Screen
- Orient the laptop keyboard-side up.
- Use tweezers to remove the adhesive covers for the screws.
Orient the laptop keyboard-side up.
Use tweezers to remove the adhesive covers for the screws.
Step 3
- Remove the two 6mm screws with a Phillips #0 screwdriver.
Remove the two 6mm screws with a Phillips #0 screwdriver.
Step 4
- Pull the bezel away from the screen.
- Be sure to go one edge at a time! Do not pull hard on the corners as it may crack the bezel.
Pull the bezel away from the screen.
Be sure to go one edge at a time! Do not pull hard on the corners as it may crack the bezel.
Step 5
- Remove the four 3mm screws with a Phillips #0 screwdriver near the corners of the screen to remove the display.
- Be careful not to confuse any screws. They are close together and you may remove the back cover instead of the display.
Remove the four 3mm screws with a Phillips #0 screwdriver near the corners of the screen to remove the display.
Be careful not to confuse any screws. They are close together and you may remove the back cover instead of the display.
Step 6
- Do not peel the tape from the side closest to the bottom of the screen panel! This may rip out the connector’s wires.
- Gently lower the screen and lay it face down on the keyboard.
- Lift the corners of the tape closest to the top of the screen and peel toward the center carefully.
- Slowly pull the tape away from the sides.
- Lift the tape and disconnect the screen connector.
- You can leave the tape stuck to the cable connector and still be able to remove it.
Do not peel the tape from the side closest to the bottom of the screen panel! This may rip out the connector’s wires.
Gently lower the screen and lay it face down on the keyboard.
Lift the corners of the tape closest to the top of the screen and peel toward the center carefully.
Slowly pull the tape away from the sides.
Lift the tape and disconnect the screen connector.
You can leave the tape stuck to the cable connector and still be able to remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
8 other people completed this guide.
Author
with 4 other contributors
Grant Terris
Member since: 01/30/2015
2,756 Reputation
12 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team 8-43, Amido Winter 2015
Member of Cal Poly, Team 8-43, Amido Winter 2015
CPSU-AMIDO-W15S8G43
4 Members
15 Guides authored
dwakefield - Aug 13, 2018
Reply
Worked great! Only caution that I would add is that on one of the machines I took apart, the adhesive strip behind the bottom of the bezel stuck to the bezel and not the circuit board behind. I had to carefully slide my finger between the adhesive strip and the bezel to separate them. Once the bezel was removed, I was able to stick the adhesive back down. I think this laptop may have been exposed to some sort of liquid, so this may not be a common issue.
H B - Sep 24, 2019
Reply
My ZBook 15u g5 does not have any adhesive covers around the screen. How do I replace?
Mohand Almohands - Aug 14, 2021
Reply
Hello can i replace my hd screen with another fhd one?
