Hp W2216H Video Port Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Screen
7 steps
Speakers
4 steps
Video Port Board
4 steps

Flags

BackHP w2216h
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

‘Make sure you are grounded, the power supply is not connected and you are wearing safety goggles.
Use the Philips #000 screwdriver to remove the 4 round12mm screws on the back panel.

‘Make sure you are grounded, the power supply is not connected and you are wearing safety goggles.

Use the Philips #000 screwdriver to remove the 4 round12mm screws on the back panel.

1024

Step 2

Using a Philips #000 head remove 2 flat 12 mm screws above stand mounting bracket.
Using a PH1 Philips head with the 150 mm flexible extension remove 1 Philips head screw under the stand mounting bracket.
Stand will easily pull off.

Using a Philips #000 head remove 2 flat 12 mm screws above stand mounting bracket.

Using a PH1 Philips head with the 150 mm flexible extension remove 1 Philips head screw under the stand mounting bracket.

Stand will easily pull off.

Step 3

Do not put the metal spudger between the metal and the glass. It needs to go under the bezel and above the metal.
Turn monitor so that the screen is facing you.
Pry the black bezel from above the metal by placing your metal spudger between the bezel and the metal and twisting the tool slightly.
The best places to pry are in the lower left and lower right corners of the black bezel.

Do not put the metal spudger between the metal and the glass. It needs to go under the bezel and above the metal.

Turn monitor so that the screen is facing you.

Pry the black bezel from above the metal by placing your metal spudger between the bezel and the metal and twisting the tool slightly.

The best places to pry are in the lower left and lower right corners of the black bezel.

Step 4

Be careful of the wires attaching the power button and the control buttons. Show extreme caution to ensure the button is not damaged.
Lift the screen assembly from the plastic housing from the corners.

Be careful of the wires attaching the power button and the control buttons. Show extreme caution to ensure the button is not damaged.

Lift the screen assembly from the plastic housing from the corners.

Step 5

Remove the 4 connectors from the left side of the monitor on the back.

Remove the 4 connectors from the left side of the monitor on the back.

Step 6

Lift the gray tape of the top of the monitor to expose the ribbon cable.
Remove the ribbon cable by sliding the connector towards the center of the screen assembly.
Lift the reflective tape next to the gray tape.

Lift the gray tape of the top of the monitor to expose the ribbon cable.

Remove the ribbon cable by sliding the connector towards the center of the screen assembly.

Lift the reflective tape next to the gray tape.

Step 7

Remove the 4 PH1 8mm Philips round screws on the outer edge of the screen’s assembly.
Lift the screen from the screen assembly.

Remove the 4 PH1 8mm Philips round screws on the outer edge of the screen’s assembly.

Lift the screen from the screen assembly.

Step 8

              Speakers

Remove the tape holding each speakers wire to the screen assembly.

Remove the tape holding each speakers wire to the screen assembly.

Step 9

Remove the two 8mm Philips #000 head screws on each speaker.

Remove the two 8mm Philips #000 head screws on each speaker.

Step 10

Remove the speakers by lifting them vertically from the screen assembly.

Remove the speakers by lifting them vertically from the screen assembly.

Step 11

Remove the cables that connects the speakers to the signal output board.

Remove the cables that connects the speakers to the signal output board.

Step 12

              Video Port Board

Remove the single Phillips #000 head screw above the HDMI port .

Remove the single Phillips #000 head screw above the HDMI port .

Step 13

Remove the two 2.5mm hex screws on either side of the VGA port

Remove the two 2.5mm hex screws on either side of the VGA port

Step 14

Remove all 8mm Phillips #000 screws holding the board in place.
Remove the ribbon cable towards the bottom of the board by sliding the cable away from the board.
Remove both wire busses still on the board.

Remove all 8mm Phillips #000 screws holding the board in place.

Remove the ribbon cable towards the bottom of the board by sliding the cable away from the board.

Remove both wire busses still on the board.

Step 15

Lift the board out of the screen assembly by first pulling the board away from the wall where the ports mount, then upward.

Lift the board out of the screen assembly by first pulling the board away from the wall where the ports mount, then upward.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Branflakes222

Member since: 03/25/2016

393 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       UMass Dartmouth, Team 1-1, Miles Spring 2016                        

                                                  Member of UMass Dartmouth, Team 1-1, Miles Spring 2016 



                    UMASSD-MILES-S16S1G1                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team