Difficulty
Moderate
Steps
13
Time Required
20 minutes
Sections
2
- Top Cover/Keyboard
- 10 steps
- WLAN Module
- 3 steps
Flags
0
BackHP Stream 13-c110nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Top Cover/Keyboard
- Close the device.
- Remove AC adapter plug from electrical outlet.
- Remove AC adapter from device.
- Turn the device off.
- Unplug all external devices from device.
- If you are unsure whether the computer is off or in hibernation mode, start the computer and then shutdown the operating system.
Close the device.
Remove AC adapter plug from electrical outlet.
Remove AC adapter from device.
Turn the device off.
Unplug all external devices from device.
If you are unsure whether the computer is off or in hibernation mode, start the computer and then shutdown the operating system.
1024
Step 2
- Turn the device upside down with the back facing towards you.
Turn the device upside down with the back facing towards you.
Step 3
- Use a pick to remove the two (2) large computer feet along the back edge of the device.
- Use a pick to remove the two (2) small computer feet.
- Use a pick to remove the one (1) screw cover.
- Place rubber computer feet in safe place for reassembly.
Use a pick to remove the two (2) large computer feet along the back edge of the device.
Use a pick to remove the two (2) small computer feet.
Use a pick to remove the one (1) screw cover.
Place rubber computer feet in safe place for reassembly.
Step 4
- Remove the thirteen (13) Phillips P0 PM2.5x6.0 mm screws.
- Place the thirteen (13) screws on magnetic mat for reassembly.
Remove the thirteen (13) Phillips P0 PM2.5x6.0 mm screws.
Place the thirteen (13) screws on magnetic mat for reassembly.
Step 5
- Turn the device over with the front facing towards you.
- Open the device as shown.
Turn the device over with the front facing towards you.
Open the device as shown.
Step 6
- Insert the Spudger between the Top Cover and Bottom Cover to lift the front edge until it separates from the Bottom Cover.
- Do not completely remove the Keyboard/Top cover from the Bottom cover yet.
Insert the Spudger between the Top Cover and Bottom Cover to lift the front edge until it separates from the Bottom Cover.
Do not completely remove the Keyboard/Top cover from the Bottom cover yet.
Step 7
- Disconnect the Touchpad cable.
Disconnect the Touchpad cable.
Step 8
- Disconnect the Keyboard Cable.
Disconnect the Keyboard Cable.
Step 9
- Disconnect the Power connector cable.
Disconnect the Power connector cable.
Step 10
- Remove the Keyboard/Top Cover from the device.
Remove the Keyboard/Top Cover from the device.
Step 11
WLAN Module
- Disconnect the WLAN antenna cable from the WLAN module.
Disconnect the WLAN antenna cable from the WLAN module.
Step 12
- Remove one (1) Phillips P0 PM2.0x3.0 mm screw.
- Place one (1) screw on magnetic mat for reassembly.
Remove one (1) Phillips P0 PM2.0x3.0 mm screw.
Place one (1) screw on magnetic mat for reassembly.
Step 13
- Remove the WLAN Module from device.
Remove the WLAN Module from device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Stacey Deel
Member since: 01/31/2019
1,147 Reputation
9 Guides authored
Badges:
12
+9 more badges
Team
Appalachian State University, Team S1-G2, Menagarishvili Spring 2019
Member of Appalachian State University, Team S1-G2, Menagarishvili Spring 2019
APSU-MENAGARISHVILI-S19S1G2
4 Members
16 Guides authored
