Difficulty

Moderate

Steps

18

Time Required

                          20 minutes

Sections

2

  • Top Cover/Keyboard
  • 10 steps
  • Display Assembly
  • 8 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHP Stream 13-c110nr

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Cover/Keyboard
  • Close the device.
  • Remove AC adapter plug from electrical outlet.
  • Remove AC adapter from device.
  • Turn the device off.
  • Unplug all external devices from device.
  • If you are unsure whether the computer is off or in hibernation mode, start the computer and then shutdown the operating system.

Close the device.

Remove AC adapter plug from electrical outlet.

Remove AC adapter from device.

Turn the device off.

Unplug all external devices from device.

If you are unsure whether the computer is off or in hibernation mode, start the computer and then shutdown the operating system.

1024

Step 2

  • Turn the device upside down with the back facing towards you.

Turn the device upside down with the back facing towards you.

Step 3

  • Use a pick to remove the two (2) large computer feet along the back edge of the device.
  • Use a pick to remove the two (2) small computer feet.
  • Use a pick to remove the one (1) screw cover.
  • Place rubber computer feet in safe place for reassembly.

Use a pick to remove the two (2) large computer feet along the back edge of the device.

Use a pick to remove the two (2) small computer feet.

Use a pick to remove the one (1) screw cover.

Place rubber computer feet in safe place for reassembly.

Step 4

  • Remove the thirteen (13) Phillips P0 PM2.5x6.0 mm screws.
  • Place the thirteen (13) screws on magnetic mat for reassembly.

Remove the thirteen (13) Phillips P0 PM2.5x6.0 mm screws.

Place the thirteen (13) screws on magnetic mat for reassembly.

Step 5

  • Turn the device over with the front facing towards you.
  • Open the device as shown.

Turn the device over with the front facing towards you.

Open the device as shown.

Step 6

  • Insert the Spudger between the Top Cover and Bottom Cover to lift the front edge until it separates from the Bottom Cover.
  • Do not completely remove the Keyboard/Top cover from the Bottom cover yet.

Insert the Spudger between the Top Cover and Bottom Cover to lift the front edge until it separates from the Bottom Cover.

Do not completely remove the Keyboard/Top cover from the Bottom cover yet.

Step 7

  • Disconnect the Touchpad cable.

Disconnect the Touchpad cable.

Step 8

  • Disconnect the Keyboard Cable.

Disconnect the Keyboard Cable.

Step 9

  • Disconnect the Power connector cable.

Disconnect the Power connector cable.

Step 10

  • Remove the Keyboard/Top Cover from the device.

Remove the Keyboard/Top Cover from the device.

Step 11

              Display Assembly
  • Disconnect the Display Cable from the System Board.

Disconnect the Display Cable from the System Board.

Step 12

  • Remove the four (4) Phillips P0 PM2.5x4.5 mm screws from the screen retaining brackets.
  • Place the four (4) screws on the magnetic mat for reassembly.

Remove the four (4) Phillips P0 PM2.5x4.5 mm screws from the screen retaining brackets.

Place the four (4) screws on the magnetic mat for reassembly.

Step 13

  • Peel off two (2) stickers located at the bottom corners of the display assembly.
  • Place two (2) stickers in safe place for reassembly.

Peel off two (2) stickers located at the bottom corners of the display assembly.

Place two (2) stickers in safe place for reassembly.

Step 14

  • Remove the two (2) Phillips P0 PM2.5x2.0 mm screws.
  • Place the two (2) screws on the magnetic mat for reassembly.

Remove the two (2) Phillips P0 PM2.5x2.0 mm screws.

Place the two (2) screws on the magnetic mat for reassembly.

Step 15

  • Use a pick to pry off the display cover from the display.

Use a pick to pry off the display cover from the display.

Step 16

  • Remove the Display Assembly.

Remove the Display Assembly.

Step 17

  • Remove the four (4) Phillips P0 PM2.5x4.5 mm screws.
  • Place four (4) screws on magnetic mat for reassembly.
  • Remove the two (2) Phillips P0 PM2.5x3.0 mm screws.
  • Place two (2) screws on magnetic mat for reassembly.

Remove the four (4) Phillips P0 PM2.5x4.5 mm screws.

Place four (4) screws on magnetic mat for reassembly.

Remove the two (2) Phillips P0 PM2.5x3.0 mm screws.

Place two (2) screws on magnetic mat for reassembly.

Step 18

  • Separate display from back cover

Separate display from back cover

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Stacey Deel

Member since: 01/31/2019

1,147 Reputation

                                      9 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Appalachian State University, Team S1-G2, Menagarishvili Spring 2019                        

                                                  Member of Appalachian State University, Team S1-G2, Menagarishvili Spring 2019 



                    APSU-MENAGARISHVILI-S19S1G2                     


                                            4 Members                     


                                            16 Guides authored