Difficulty
Moderate
Steps
15
Time Required
30 minutes
Sections
2
- Keyboard
- 5 steps
- Screen
- 10 steps
Flags
0
BackHP Stream 11-y010nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Keyboard
- Gently peel back the two rubber strips that cover the screws on backside of the computer with the needle nose tweezers.
- Ensure the laptop is turned off.
Gently peel back the two rubber strips that cover the screws on backside of the computer with the needle nose tweezers.
Ensure the laptop is turned off.
1024
Step 2
- Unscrew the seven 0.4mm screws on the backside of the laptop with the Phillips #0 Screwdriver.
Unscrew the seven 0.4mm screws on the backside of the laptop with the Phillips #0 Screwdriver.
Step 3
- Take the opening picks and push them into the seam between the keyboard and the laptop casing.
- Go all the way around the laptop.
Take the opening picks and push them into the seam between the keyboard and the laptop casing.
Go all the way around the laptop.
Step 4
- Once the cover is loose enough, lift the keyboard up to expose the wiring beneath.
- Be careful not to pull too hard or fast as there are ribbon cables attached to the keyboard and trackpad.
Once the cover is loose enough, lift the keyboard up to expose the wiring beneath.
Be careful not to pull too hard or fast as there are ribbon cables attached to the keyboard and trackpad.
Step 5
- Disconnect the three cables by lifting up on the locking tab of the ZIF connector and pulling the cables out with the needle nose tweezers.
- Remove the keyboard.
Disconnect the three cables by lifting up on the locking tab of the ZIF connector and pulling the cables out with the needle nose tweezers.
Remove the keyboard.
Step 6
Screen
- Using your fingers or a spudger, pull the battery cable from its connector to disconnect power from the motherboard.
Using your fingers or a spudger, pull the battery cable from its connector to disconnect power from the motherboard.
Step 7
- Insert iFixit opening picks into the edges of the screen to break the seal between the screen and bezel.
Insert iFixit opening picks into the edges of the screen to break the seal between the screen and bezel.
Step 8
- Peel the hinge up by sliding iFixit opening picks left to right along the hinge.
Peel the hinge up by sliding iFixit opening picks left to right along the hinge.
Step 9
- Remove the bezel by pulling upwards on the left bottom corner.
Remove the bezel by pulling upwards on the left bottom corner.
Step 10
- Disconnect the screen from the motherboard by pulling the display cable from its connector.
Disconnect the screen from the motherboard by pulling the display cable from its connector.
Step 11
- Unscrew the four 0.4mm screws surrounding the display using a Phillips #00 screwdriver.
Unscrew the four 0.4mm screws surrounding the display using a Phillips #00 screwdriver.
Step 12
- Gently remove the screen from its holding and lay the screen down on the keyboard. It is still attached to the computer.
Gently remove the screen from its holding and lay the screen down on the keyboard. It is still attached to the computer.
Step 13
- Take the tweezers and push up on the small connector to the left of the webcam.
Take the tweezers and push up on the small connector to the left of the webcam.
Step 14
- Gently pull the cord out from around the screen area.
Gently pull the cord out from around the screen area.
Step 15
- Remove the screen with the display cable attached.
Remove the screen with the display cable attached.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Adam Sitzmann
Member since: 01/26/2020
914 Reputation
6 Guides authored
Badges:
8
+5 more badges
Team
Embry-Riddle Aeronautical University, Team S5-G6, Watkins Spring 2020
Member of Embry-Riddle Aeronautical University, Team S5-G6, Watkins Spring 2020
ERAU-WATKINS-S20S5G6
4 Members
6 Guides authored
