Difficulty
Moderate
Steps
11
Time Required
15 - 25 minutes
Sections
1
- Battery
- 11 steps
Flags
0
BackHP Stream 11-r020nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Turn off your HP Stream 11-r020nr by holding the power button down for 10 seconds.
- Turn the device top down so the rubber feet are facing up.
- Use a metal spudger to remove all the rubber feet off of the bottom of the device, including the small ones. This will uncover 6 screws for a total of 11 screws.
Turn off your HP Stream 11-r020nr by holding the power button down for 10 seconds.
Turn the device top down so the rubber feet are facing up.
Use a metal spudger to remove all the rubber feet off of the bottom of the device, including the small ones. This will uncover 6 screws for a total of 11 screws.
1024
Step 2
- Using the Phillips #1 screwdriver, remove all eleven of the 5mm screws.
Using the Phillips #1 screwdriver, remove all eleven of the 5mm screws.
Step 3
- Flip the laptop over and open.
- Using the blue plastic opening tool, separate the keyboard plate from the main body by prying up starting around the bottom corners, prying the bottom up and all the way around the whole keyboard plate.
Flip the laptop over and open.
Using the blue plastic opening tool, separate the keyboard plate from the main body by prying up starting around the bottom corners, prying the bottom up and all the way around the whole keyboard plate.
Step 4
- Use the black nylon spudger to flip the black tab up that holds the ribbon cable in place.
- Lift the ribbon cable free.
Use the black nylon spudger to flip the black tab up that holds the ribbon cable in place.
Lift the ribbon cable free.
Step 5
- Use the black nylon spudger to flip the black tab up that holds the large ribbon cable in place.
- Pull the ribbon cable free from the base of the keyboard.
Use the black nylon spudger to flip the black tab up that holds the large ribbon cable in place.
Pull the ribbon cable free from the base of the keyboard.
Step 6
- Remove the tape covering the ribbon cable.
- Use the black nylon spudger to flip the black tab up that holds the ribbon cable in place.
- Pull the ribbon cable away from the base of the laptop.
Remove the tape covering the ribbon cable.
Pull the ribbon cable away from the base of the laptop.
Step 7
- After detaching the two large ribbon cables, carefully lean the keyboard against the screen.
After detaching the two large ribbon cables, carefully lean the keyboard against the screen.
Step 8
- With the black nylon spudger lift the small circular battery off of the main battery.
With the black nylon spudger lift the small circular battery off of the main battery.
Step 9
- Lift the battery cable free from the motherboard with your fingers.
Lift the battery cable free from the motherboard with your fingers.
Step 10
- Gently pull the wire away from the battery.
- Using the Phillips #1 screwdriver, remove the six 3mm screws.
Gently pull the wire away from the battery.
Using the Phillips #1 screwdriver, remove the six 3mm screws.
Step 11
- Gently lift and pull the battery out of the device.
Gently lift and pull the battery out of the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Bailey Webb
Member since: 04/09/2018
297 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
Eastern Washington University, Team S1-G1, Carnegie Spring 2018
Member of Eastern Washington University, Team S1-G1, Carnegie Spring 2018
EWU-CARNEGIE-S18S1G1
4 Members
8 Guides authored
