Difficulty
Moderate
Steps
8
Time Required
45 minutes
Sections
1
- Screen
- 8 steps
Flags
0
BackHP Stream 11-r014wm
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Use a plastic spudger to remove two oblong screw covers on the bottom of the computer.
- Use a plastic spudger to remove four rubber feet.
- To remove the feet you must break the glue seal holding them down.
Use a plastic spudger to remove two oblong screw covers on the bottom of the computer.
Use a plastic spudger to remove four rubber feet.
To remove the feet you must break the glue seal holding them down.
1024
Step 2
- Remove the eleven 5 millimeter housing screws from the bottom of the computer using a #00 Phillips head screwdriver.
Remove the eleven 5 millimeter housing screws from the bottom of the computer using a #00 Phillips head screwdriver.
Step 3
- Turn the computer over and open it.
- Use a plastic spudger to pry the keyboard bezel away from the base. Pry around the edge, being careful not to jam the spudger too far underneath the bezel (potentially damaging internal components).
- The bezel is tightest near the hinge.
- Once the bezel is free, do not lift it away from the base.
Turn the computer over and open it.
Use a plastic spudger to pry the keyboard bezel away from the base. Pry around the edge, being careful not to jam the spudger too far underneath the bezel (potentially damaging internal components).
The bezel is tightest near the hinge.
Once the bezel is free, do not lift it away from the base.
Step 4
- Identify two ribbon connectors and the ZIF cable underneath the keyboard.
- Use tweezers to disconnect both ribbon cables and the ZIF connector.
Identify two ribbon connectors and the ZIF cable underneath the keyboard.
Use tweezers to disconnect both ribbon cables and the ZIF connector.
Step 5
- Remove five 4 millimeter hinge-screws using a #00 Phillips head screwdriver.
- There are three 4 millimeter hinge-screws on the right side.
Remove five 4 millimeter hinge-screws using a #00 Phillips head screwdriver.
There are three 4 millimeter hinge-screws on the right side.
Step 6
- Use tweezers to disconnect the black power cable.
- Remove the 3.5 millimeter screw from the WiFi chip using a #00 Phillips head screwdriver.
- The upper and lower halves of the laptop should now be separated.
Use tweezers to disconnect the black power cable.
Remove the 3.5 millimeter screw from the WiFi chip using a #00 Phillips head screwdriver.
The upper and lower halves of the laptop should now be separated.
Step 7
- Remove two 2 millimeter bezel screws using a #00 Phillips screwdriver.
- Use a plastic spudger to pry the bezel away from the screen.
- The bezel screws are covered by thin plastic.
Remove two 2 millimeter bezel screws using a #00 Phillips screwdriver.
Use a plastic spudger to pry the bezel away from the screen.
The bezel screws are covered by thin plastic.
Step 8
- Remove four 3 millimeter screen screws using a #00 Phillips head screwdriver.
- Lift the screen with steady pressure until the glue seal breaks and releases the lid.
Remove four 3 millimeter screen screws using a #00 Phillips head screwdriver.
Lift the screen with steady pressure until the glue seal breaks and releases the lid.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Anthony R Cardinali
Member since: 04/05/2018
988 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Linn Benton Community College, Team S1-G3, Johnson Spring 2018
Member of Linn Benton Community College, Team S1-G3, Johnson Spring 2018
LBCC-JOHNSON-S18S1G3
4 Members
5 Guides authored
