Difficulty

Moderate

Steps

15

Time Required

                          15 - 20 minutes

Sections

4

  • Keyboard
  • 6 steps
  • Battery
  • 2 steps
  • Wifi Chip
  • 2 steps
  • Webcam
  • 5 steps

Flags

0

  • BackHP Stream 11-d010nr

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard
  • Unplug and turn off the HP Stream 11 before disassembling the device.
  • Pry off the two elliptical rubber inserts (one in each corner).
  • Pry off the two circular rubber inserts below the removed elliptical inserts (one in each corner).

Unplug and turn off the HP Stream 11 before disassembling the device.

Pry off the two elliptical rubber inserts (one in each corner).

Pry off the two circular rubber inserts below the removed elliptical inserts (one in each corner).

1024

Step 2

  • Remove the eleven 5.6 mm Phillips #1 screws.

Remove the eleven 5.6 mm Phillips #1 screws.

Step 3

  • Using an iFixit opening tool, pry open the case to separate the keyboard from the main body.
  • HP Stream 11s tend to be really difficult to open. If your device is not opening with a standard iFixit opening tool, use a nylon spudger, then the metal spudger, or a metal Jimmy as the last resort.
  • When using the metal spudger or Jimmy, be careful not to bring these tools into contact with any electronic components of the device as this can damage the device.

Using an iFixit opening tool, pry open the case to separate the keyboard from the main body.

HP Stream 11s tend to be really difficult to open. If your device is not opening with a standard iFixit opening tool, use a nylon spudger, then the metal spudger, or a metal Jimmy as the last resort.

When using the metal spudger or Jimmy, be careful not to bring these tools into contact with any electronic components of the device as this can damage the device.

Step 4

  • Slowly lift the keyboard as there are multiple ribbon cables that could easily be damaged if lifted with force.
  • Carefully lift the keyboard and locate the three ribbon cables connecting the main body of the laptop to the keyboard.

Slowly lift the keyboard as there are multiple ribbon cables that could easily be damaged if lifted with force.

Carefully lift the keyboard and locate the three ribbon cables connecting the main body of the laptop to the keyboard.

Step 5

  • Using your fingernail, lift the flaps on the ZIF connectors that are securing the three ribbon cables.
  • Carefully disconnect the three ribbon cables.

Using your fingernail, lift the flaps on the ZIF connectors that are securing the three ribbon cables.

Carefully disconnect the three ribbon cables.

Step 6

  • Lift the keyboard out of the laptop to remove it from the device.

Lift the keyboard out of the laptop to remove it from the device.

Step 7

              Battery
  • Remove any tape holding the battery connector in place.
  • Using your fingers, carefully unplug the battery.

Remove any tape holding the battery connector in place.

Using your fingers, carefully unplug the battery.

Step 8

  • Remove the four 3mm #000 Phillips screws holding the battery in place.
  • Carefully lift the battery out of the laptop.

Remove the four 3mm #000 Phillips screws holding the battery in place.

Carefully lift the battery out of the laptop.

Step 9

              Wifi Chip
  • Unplug the black wire attached to the wireless chip.

Unplug the black wire attached to the wireless chip.

Step 10

  • Remove the one 3mm Phillips #000 screw holding the wireless chip in place.
  • Lift the wireless chip up and out.

Remove the one 3mm Phillips #000 screw holding the wireless chip in place.

Lift the wireless chip up and out.

Step 11

              Webcam
  • Flip up the flap and unplug the display cord from the motherboard.

Flip up the flap and unplug the display cord from the motherboard.

Step 12

  • Using a JIS #1 screwdriver, remove the four 2.2 mm screws holding monitor to body.

Using a JIS #1 screwdriver, remove the four 2.2 mm screws holding monitor to body.

Step 13

  • Use tweezers to remove the screw covers from the lid.
  • Unscrew the two 2.2 mm #000 Phillips screws.

Use tweezers to remove the screw covers from the lid.

Unscrew the two 2.2 mm #000 Phillips screws.

Step 14

  • Open the upper lid with the iFixit opening tool.

Open the upper lid with the iFixit opening tool.

Step 15

  • Disconnect the webcam cord using tweezers.
  • Remove the webcam using tweezers.

Disconnect the webcam cord using tweezers.

Remove the webcam using tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Zachary Heisler

Member since: 01/24/2019

352 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S1-G3, White Winter 2019                        

                                                  Member of Cal Poly, Team S1-G3, White Winter 2019 



                    CPSU-WHITE-W19S1G3                     


                                            4 Members                     


                                            11 Guides authored