Difficulty

Moderate

Steps

9

Time Required

                          15 - 25 minutes

Sections

2

  • Outer Casing
  • 7 steps
  • Battery
  • 2 steps

Flags

0

  • BackHP Sprocket 2-in-1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Casing
  • Remove the back cover and any printer paper inside the device.

Remove the back cover and any printer paper inside the device.

1024

Step 2

  • Using the Jimmy, slowly pry open the outer edge of the remaining white plastic on the back.
  • Remove the plastic from the device once it lifts out freely.

Using the Jimmy, slowly pry open the outer edge of the remaining white plastic on the back.

Remove the plastic from the device once it lifts out freely.

Step 3

  • Remove two 2.5mm JIS #00 located on the small circuit board in view.
  • Use the Jimmy to remove the board after the screws have been removed.
  • Be careful not to crease or damage the ribbon cable.

Remove two 2.5mm JIS #00 located on the small circuit board in view.

Use the Jimmy to remove the board after the screws have been removed.

Be careful not to crease or damage the ribbon cable.

Step 4

  • Remove two 2.5mm JIS #00 screws from the translucent plastic bracket.
  • One will be located beneath the ribbon cable.
  • Remove the translucent plastic bracket by hand.

Remove two 2.5mm JIS #00 screws from the translucent plastic bracket.

One will be located beneath the ribbon cable.

Remove the translucent plastic bracket by hand.

Step 5

  • Remove four 2.5mm JIS #00 screws from the beige casing.

Remove four 2.5mm JIS #00 screws from the beige casing.

Step 6

  • Use the iFixit opening tool to slowly work between the white and beige casing around the device.
  • Flip the device over and seperate the white casing from the rest of the device.
  • Be careful not to break the plastic while removing the case.
  • Gently remove the white casing as there is a ribbon cable connecting the two pieces.

Use the iFixit opening tool to slowly work between the white and beige casing around the device.

Flip the device over and seperate the white casing from the rest of the device.

Be careful not to break the plastic while removing the case.

Gently remove the white casing as there is a ribbon cable connecting the two pieces.

Step 7

  • Carefully remove the ribbon cable that connects the flash to the outer casing.

Carefully remove the ribbon cable that connects the flash to the outer casing.

Step 8

              Battery
  • Use a JIS #00 screwdriver to remove a single black screw near the viewfinder.
  • Remove a single silver 2.5mm JIS #00 screw near the USB port of the device.
  • Carefully remove the metal bracket.

Use a JIS #00 screwdriver to remove a single black screw near the viewfinder.

Remove a single silver 2.5mm JIS #00 screw near the USB port of the device.

Carefully remove the metal bracket.

Step 9

  • Work the battery free from the device with the iFixit opening tool.
  • Carefully disconnect the battery from the board.

Work the battery free from the device with the iFixit opening tool.

Carefully disconnect the battery from the board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Paulo Warren

Member since: 02/05/2019

437 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       University of Michigan, Team S1-G4, Li Winter 2019                        

                                                  Member of University of Michigan, Team S1-G4, Li Winter 2019 



                    UMIC-LI-W19S1G4                     


                                            4 Members                     


                                            5 Guides authored

Big Peltch - Aug 23, 2019

Reply

Awesome guide. Just turned on my sprocket after 9 months and the battery is definitely dead. I will definitely be using your guide in the days to come. But where did you get the replacement battery from?

Cheers,

Michael Staats - Mar 30, 2020

Did you ever figure out where to buy a battery?

Daniel Stizza - Sep 9, 2020

Reply

Hola, donde puedo comprar la bateria de HP Sprocket 100? Li-ion Polymer Battery Model: P0562-LF. Desde ya muchas gracias.

Fernando - Oct 4, 2020

Reply

Muy bonito todo.

Acudí al soporte HP y me dicen que no hay batería de reemplazo. La he buscado en muchos sitios y nada.

¿En qué sitio la podré conseguir?

Daniel Stizza - Nov 13, 2020

Reply

Hello, where can I buy the battery for HP Sprocket 100? Li-ion Polymer Battery Model: P0562-LF. From already thank you very much.

I went to HP support and they tell me there is no replacement battery. I have looked for it in many places and nothing.