Difficulty
Moderate
Steps
18
Time Required
20 minutes
Sections
6
- Back Panel
- 1 step
- Battery
- 3 steps
- Docking Port
- 4 steps
- SD Port
- 3 steps
- Audio Port
- 4 steps
- Speakers
- 3 steps
Flags
2
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackHP Split x2 13-g210dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Carefully peel off the felt cover that is found beneath the display along the bottom of the device.
- Use a spudger to gently scrape away the padding that hides the screws in each of the four locations.
- Remove the four 4-mm Phillips #0 screws.
- Run a spudger along the crease of the entire laptop and slowly pry off the back panel of the device, beginning with the bottom edge.
- You will hear popping noises as the clips separate from each other.
Carefully peel off the felt cover that is found beneath the display along the bottom of the device.
Use a spudger to gently scrape away the padding that hides the screws in each of the four locations.
Remove the four 4-mm Phillips #0 screws.
Run a spudger along the crease of the entire laptop and slowly pry off the back panel of the device, beginning with the bottom edge.
You will hear popping noises as the clips separate from each other.
1024
Step 2
Battery
- Remove the three 6-mm Phillips #0 screws.
- Remove the four 4-mm Phillips #0 screws.
Remove the three 6-mm Phillips #0 screws.
Step 3
- Remove the white connector clip from the connector port using a sturdy tweezers.
Remove the white connector clip from the connector port using a sturdy tweezers.
Step 4
- Lift the battery away from the device.
Lift the battery away from the device.
Step 5
Docking Port
- Remove the two 4-mm Phillips #0 screws.
Remove the two 4-mm Phillips #0 screws.
Step 6
- Remove the clips from the docking port board with a sturdy pair of tweezers.
Remove the clips from the docking port board with a sturdy pair of tweezers.
Step 7
- Remove the two ribbons labeled “Dock” at the top of the docking port board using tweezers or a sturdy plastic opening tool.
Remove the two ribbons labeled “Dock” at the top of the docking port board using tweezers or a sturdy plastic opening tool.
Step 8
- Lift the docking port away from the device.
Lift the docking port away from the device.
Step 9
SD Port
Step 10
- Remove the yellow ribbon labeled “SD” in the left corner of the SD port board using tweezers or a sturdy plastic opening tool.
Remove the yellow ribbon labeled “SD” in the left corner of the SD port board using tweezers or a sturdy plastic opening tool.
Step 11
- Lift the SD port away from the device.
Lift the SD port away from the device.
Step 12
Audio Port
Step 13
- Remove the two purple ribbons labeled “Audio” at the top of the audio port board using tweezers or a sturdy plastic opening tool.
Remove the two purple ribbons labeled “Audio” at the top of the audio port board using tweezers or a sturdy plastic opening tool.
Step 14
- Remove the white clip at the top right corner of the audio port board using tweezers.
Remove the white clip at the top right corner of the audio port board using tweezers.
Step 15
- Lift the Audio port away from the device.
Lift the Audio port away from the device.
Step 16
Speakers
- Remove the 4-mm Phillips #0 screw.
- Lift the left speaker away from the device.
Remove the 4-mm Phillips #0 screw.
Lift the left speaker away from the device.
Step 17
- Remove the 4-mm Phillips #0 screw from the same location as found on the left speaker.
- Lift the right speaker away from the device.
Remove the 4-mm Phillips #0 screw from the same location as found on the left speaker.
Lift the right speaker away from the device.
Step 18
- Carefully remove the bonded white and black speaker wires running along the bottom of the control board from the fastening clips.
- Lift the speaker assembly away from the device.
Carefully remove the bonded white and black speaker wires running along the bottom of the control board from the fastening clips.
Lift the speaker assembly away from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Darian Devries
Member since: 02/25/2019
495 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
Purdue University Northwest, Team S4-G1, Hingst Spring 2019
Member of Purdue University Northwest, Team S4-G1, Hingst Spring 2019
PNW-HINGST-S19S4G1
4 Members
6 Guides authored
