Difficulty

Easy

Steps

8

Time Required

                          10 minutes

Sections

2

  • Front and Back Panel
  • 4 steps
  • Speaker
  • 4 steps

Flags

0

  • BackHP Split X2 13-r000 Series

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Front and Back Panel
  • Locate the four screws at the bottom of the device. (Note that the keyboard attachment is missing from this device.)
  • Use a Philips head #0 screwdriver to remove each of the screws (Size: 4mm)

Locate the four screws at the bottom of the device. (Note that the keyboard attachment is missing from this device.)

Use a Philips head #0 screwdriver to remove each of the screws (Size: 4mm)

1024

Step 2

  • Gently wedge the plastic opening tool in between where the display and back panel meet.
  • Slowly and gently apply force to the plastic opening tool in a downwards motion to loosen the front panel from the back panel.
  • Rotate the device so that the side is facing up and repeat the previous step for the sides.
  • Do NOT attempt to wedge the plastic opening tool on the bottom . Once the sides and top are loose you are ready to continue to the next step.

Gently wedge the plastic opening tool in between where the display and back panel meet.

Slowly and gently apply force to the plastic opening tool in a downwards motion to loosen the front panel from the back panel.

Rotate the device so that the side is facing up and repeat the previous step for the sides.

Do NOT attempt to wedge the plastic opening tool on the bottom . Once the sides and top are loose you are ready to continue to the next step.

Step 3

  • Gently and slowly pull the front and back panel away from each other (in opposite directions). ( Pulling them apart will not separate the two panels)
  • Only separate the panels by a few inches from each other so that there is room to separate the front and back panel in the next step. Proceed to the next step.

Gently and slowly pull the front and back panel away from each other (in opposite directions). ( Pulling them apart will not separate the two panels)

Only separate the panels by a few inches from each other so that there is room to separate the front and back panel in the next step. Proceed to the next step.

Step 4

  • Hold the back panel firmly and pull the front panel upwards to completely separate the front panel from the back panel.
  • The device is now ready to be repaired or replacements installed.

Hold the back panel firmly and pull the front panel upwards to completely separate the front panel from the back panel.

The device is now ready to be repaired or replacements installed.

Step 5

              Speaker
  • Using the PH 0 screw head unscrew each of the screws located int the upper right of the speakers.

Using the PH 0 screw head unscrew each of the screws located int the upper right of the speakers.

Step 6

  • After unscrewing the speakers, gently lift the speaker out using the tweezers.

After unscrewing the speakers, gently lift the speaker out using the tweezers.

Step 7

  • Once each speaker is out, remove the center plate in between the speakers, using the PH0 bit.

Once each speaker is out, remove the center plate in between the speakers, using the PH0 bit.

Step 8

  • After removing the the speakers completely, using the tweezers gently remove the micro chip connection from the system.
  • Then untwist the wires from the thick black cord.
  • Be careful when pulling the cord underneath the plug-ins marked in red. They may unplug.

After removing the the speakers completely, using the tweezers gently remove the micro chip connection from the system.

Then untwist the wires from the thick black cord.

Be careful when pulling the cord underneath the plug-ins marked in red. They may unplug.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Kim

Member since: 09/26/2017

201 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       University of North Texas, Team S2-G1, Thompson Fall 2017                        

                                                  Member of University of North Texas, Team S2-G1, Thompson Fall 2017 



                    UNT-THOMPSON-F17S2G1                     


                                            4 Members                     


                                            5 Guides authored