Difficulty
Moderate
Steps
8
Time Required
25 minutes
Sections
2
- Front and Back Panel
- 4 steps
- Screen
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackHP Split X2 13-r000 Series
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Front and Back Panel
- Locate the four screws at the bottom of the device. (Note that the keyboard attachment is missing from this device.)
- Use a Philips head #0 screwdriver to remove each of the screws (Size: 4mm)
Locate the four screws at the bottom of the device. (Note that the keyboard attachment is missing from this device.)
Use a Philips head #0 screwdriver to remove each of the screws (Size: 4mm)
1024
Step 2
- Gently wedge the plastic opening tool in between where the display and back panel meet.
- Slowly and gently apply force to the plastic opening tool in a downwards motion to loosen the front panel from the back panel.
- Rotate the device so that the side is facing up and repeat the previous step for the sides.
- Do NOT attempt to wedge the plastic opening tool on the bottom . Once the sides and top are loose you are ready to continue to the next step.
Gently wedge the plastic opening tool in between where the display and back panel meet.
Slowly and gently apply force to the plastic opening tool in a downwards motion to loosen the front panel from the back panel.
Rotate the device so that the side is facing up and repeat the previous step for the sides.
Do NOT attempt to wedge the plastic opening tool on the bottom . Once the sides and top are loose you are ready to continue to the next step.
Step 3
- Gently and slowly pull the front and back panel away from each other (in opposite directions). ( Pulling them apart will not separate the two panels)
- Only separate the panels by a few inches from each other so that there is room to separate the front and back panel in the next step. Proceed to the next step.
Gently and slowly pull the front and back panel away from each other (in opposite directions). ( Pulling them apart will not separate the two panels)
Only separate the panels by a few inches from each other so that there is room to separate the front and back panel in the next step. Proceed to the next step.
Step 4
- Hold the back panel firmly and pull the front panel upwards to completely separate the front panel from the back panel.
- The device is now ready to be repaired or replacements installed.
Hold the back panel firmly and pull the front panel upwards to completely separate the front panel from the back panel.
The device is now ready to be repaired or replacements installed.
Step 5
Screen
- Use the PH1 screwdriver to remove eleven 4mm Phillips screws.
Use the PH1 screwdriver to remove eleven 4mm Phillips screws.
Step 6
- Unscrew the two 2mm zero insertion force connectors. Slide aside the white wires to properly unscrew.
Unscrew the two 2mm zero insertion force connectors. Slide aside the white wires to properly unscrew.
Step 7
- Use a pair of tweezers to pull up the yellow colored display cable connector.
- Pull it to the direction of the cable.
Use a pair of tweezers to pull up the yellow colored display cable connector.
Pull it to the direction of the cable.
Step 8
- Glue is attached at the edges. Apply force to the sides of the tablet. Separate the digitizer from the body of the tablet.
- Replace the old screen with a new one.
- If your screen is broken or damaged, use caution when pulling the screen from the tablet to avoid self harm.
Glue is attached at the edges. Apply force to the sides of the tablet. Separate the digitizer from the body of the tablet.
Replace the old screen with a new one.
If your screen is broken or damaged, use caution when pulling the screen from the tablet to avoid self harm.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
bushraishaq
Member since: 09/25/2017
298 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
University of North Texas, Team S2-G1, Thompson Fall 2017
Member of University of North Texas, Team S2-G1, Thompson Fall 2017
UNT-THOMPSON-F17S2G1
4 Members
5 Guides authored
Martin Sala - Aug 22, 2020
Reply
Hello… How to know if it is the digitizer or the screen that is broken? .. thanks
