Hp Split 13 R010Dx Hard Drive Replacement Repair Guide

Difficulty

Very easy

Steps

Time Required

                          2 - 5 minutes

Sections

Front and Back Panel
4 steps
Hard Drive
6 steps

Flags

BackHP Split X2 13-r000 Series
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front and Back Panel

Locate the four screws at the bottom of the device. (Note that the keyboard attachment is missing from this device.)
Use a Philips head #0 screwdriver to remove each of the screws (Size: 4mm)

Locate the four screws at the bottom of the device. (Note that the keyboard attachment is missing from this device.)

Use a Philips head #0 screwdriver to remove each of the screws (Size: 4mm)

1024

Step 2

Gently wedge the plastic opening tool in between where the display and back panel meet.
Slowly and gently apply force to the plastic opening tool in a downwards motion to loosen the front panel from the back panel.
Rotate the device so that the side is facing up and repeat the previous step for the sides.
Do NOT attempt to wedge the plastic opening tool on the bottom . Once the sides and top are loose you are ready to continue to the next step.

Gently wedge the plastic opening tool in between where the display and back panel meet.

Slowly and gently apply force to the plastic opening tool in a downwards motion to loosen the front panel from the back panel.

Rotate the device so that the side is facing up and repeat the previous step for the sides.

Do NOT attempt to wedge the plastic opening tool on the bottom . Once the sides and top are loose you are ready to continue to the next step.

Step 3

Gently and slowly pull the front and back panel away from each other (in opposite directions). ( Pulling them apart will not separate the two panels)
Only separate the panels by a few inches from each other so that there is room to separate the front and back panel in the next step. Proceed to the next step.

Gently and slowly pull the front and back panel away from each other (in opposite directions). ( Pulling them apart will not separate the two panels)

Only separate the panels by a few inches from each other so that there is room to separate the front and back panel in the next step. Proceed to the next step.

Step 4

Hold the back panel firmly and pull the front panel upwards to completely separate the front panel from the back panel.
The device is now ready to be repaired or replacements installed.

Hold the back panel firmly and pull the front panel upwards to completely separate the front panel from the back panel.

The device is now ready to be repaired or replacements installed.

Step 5

              Hard Drive

Locate the hard drive. (The hard drive is located in the center of the device)

Locate the hard drive. (The hard drive is located in the center of the device)

Step 6

Locate the black strip of thermal resistant tape that is covering the upper right portion of the hard drive.
Gently lift up with the tape.
Fold the tape back away from the hard drive.

Locate the black strip of thermal resistant tape that is covering the upper right portion of the hard drive.

Gently lift up with the tape.

Fold the tape back away from the hard drive.

Step 7

Locate the four screws (Size: 4mm) at each of the four corners of the hard drive.
Remove the four screws using a #0 Phillips head screwdriver.

Locate the four screws (Size: 4mm) at each of the four corners of the hard drive.

Remove the four screws using a #0 Phillips head screwdriver.

Step 8

Locate the lift tab. (The lift tab is located at the bottom left corner of the hard drive).
Gently lift up on the lift tab
Be cautious when lifting the hard drive from its designated slot, the hard drive is still connected to the device

Locate the lift tab. (The lift tab is located at the bottom left corner of the hard drive).

Gently lift up on the lift tab

Be cautious when lifting the hard drive from its designated slot, the hard drive is still connected to the device

Step 9

Locate the connection of the hard drive to the device.
Gently grasp the connector cord and pull horizontally to the right. (Very little force is needed to disconnect the cord).

Locate the connection of the hard drive to the device.

Gently grasp the connector cord and pull horizontally to the right. (Very little force is needed to disconnect the cord).

Step 10

The hard drive is no longer connected to the device. Lift the hard drive up vertically and set aside.
The hard drive removal is completed.

The hard drive is no longer connected to the device. Lift the hard drive up vertically and set aside.

The hard drive removal is completed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors

Kim

Member since: 09/26/2017

201 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       University of North Texas, Team S2-G1, Thompson Fall 2017                        

                                                  Member of University of North Texas, Team S2-G1, Thompson Fall 2017 



                    UNT-THOMPSON-F17S2G1                     


                                            4 Members                     


                                            5 Guides authored

Pablo Cesar Zacarias - Apr 4, 2018

Is it possible to change the Wd5000m21k disk for a Wd5000m22k?

Introduction#

What you need#

Team#

Introduction

What you need

Team