Difficulty
Moderate
Steps
10
Time Required
5 - 10 minutes
Sections
3
- Cover Removal
- 3 steps
- Optical Disk Drive (CD Drive)
- 4 steps
- Power Supply
- 3 steps
Flags
0
BackHP rp5700
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Step 1
Cover Removal
- Make sure the computer is unplugged.
- Be sure to touch any metal surface with your hand to discharge any static electricity that might have built up.
- Make sure all auxiliary cords are disconnected from the desktop. If not, remove them using your hands.
- Set the desktop down horizontally with the front side facing you.
Make sure the computer is unplugged.
Be sure to touch any metal surface with your hand to discharge any static electricity that might have built up.
Make sure all auxiliary cords are disconnected from the desktop. If not, remove them using your hands.
Set the desktop down horizontally with the front side facing you.
1024
Step 2
- Hold the desktop with two hands by grasping both sides of the desktop.
- Press the buttons on both sides using your index fingers.
Hold the desktop with two hands by grasping both sides of the desktop.
Press the buttons on both sides using your index fingers.
Step 3
- Slide the top cover about an inch forward using your thumb to push it towards you.
- Make sure that the bottom is still secured by both hands.
- Lay the desktop back on the table and pull the case forward as far as it can go.
- Lift the cover up and off.
Slide the top cover about an inch forward using your thumb to push it towards you.
Make sure that the bottom is still secured by both hands.
Lay the desktop back on the table and pull the case forward as far as it can go.
Lift the cover up and off.
Step 4
Optical Disk Drive (CD Drive)
- Using your hand, grip the Optical Drive and lift it up into a 45 degree angle.
Using your hand, grip the Optical Drive and lift it up into a 45 degree angle.
Step 5
- Disconnect the power supply cord and the SATA cord using your hands to pull them out.
Disconnect the power supply cord and the SATA cord using your hands to pull them out.
Step 6
- Using your left index finger, lift the upper green tab found on the left side of the green piece.
- Using your opposite hand, use your fingers to push the back of the drive forward and slide it out away from the desktop.
Using your left index finger, lift the upper green tab found on the left side of the green piece.
Using your opposite hand, use your fingers to push the back of the drive forward and slide it out away from the desktop.
Step 7
- Grasp the optical drive with your right or left hand and pull the drive out towards you.
- It will help if you lay the device flat in order to remove the drive.
Grasp the optical drive with your right or left hand and pull the drive out towards you.
It will help if you lay the device flat in order to remove the drive.
Step 8
Power Supply
- Using your right index finger, press the tab with the green sticker located underneath the power supply.
- While pressing the tab, lift up the power supply the same way you lifted up the optical drive.
- You lifted the optical drive by grasping it with the opposite hand while pressing the tab and pulling it outward way from the center of the device.
Using your right index finger, press the tab with the green sticker located underneath the power supply.
While pressing the tab, lift up the power supply the same way you lifted up the optical drive.
You lifted the optical drive by grasping it with the opposite hand while pressing the tab and pulling it outward way from the center of the device.
Step 9
- Remove the two cables on the motherboard by grasping the cables with your hand and pulling the cables up and out.
- Repeat the same process to remove the internal card power cable.
- This is the same process as preformed when you previously removed the power cables from the optical drive and the hard drive.
- Some cables may have small clips securing them in place. If so, be sure to press these clips inward using your fingers before pulling them out.
Remove the two cables on the motherboard by grasping the cables with your hand and pulling the cables up and out.
Repeat the same process to remove the internal card power cable.
This is the same process as preformed when you previously removed the power cables from the optical drive and the hard drive.
Some cables may have small clips securing them in place. If so, be sure to press these clips inward using your fingers before pulling them out.
Step 10
- Continue to rotate the power supply to a 90 degree angle pointing upward.
- Gripping the power supply with your hand, lift the power supply up to remove from the desktop.
Continue to rotate the power supply to a 90 degree angle pointing upward.
Gripping the power supply with your hand, lift the power supply up to remove from the desktop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 4 other contributors
Alyssa Briones
Member since: 01/21/2014
1,660 Reputation
9 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 6-23, Maness Winter 2014
Member of Cal Poly, Team 6-23, Maness Winter 2014
CPSU-MANESS-W14S6G23
4 Members
9 Guides authored
jan 2332 - Aug 20, 2018
Reply
Thank you so very much for this manual! Very clear and easy to understand! Keep up the good work! Much appreciated!
