Difficulty

Moderate

Steps

12

Time Required

                          30 - 45 minutes

Sections

2

  • Scanner Glass
  • 7 steps
  • Scanner Lamp
  • 5 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackHP PSC 2410 Photosmart All In One

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Note: The scanner lamp is very fragile and must be handled with care.

What you need

Step 1

              Scanner Glass
  • Carefully wedge the flathead 3/32" screwdriver on the outer groove of the control panel faceplate.
  • Follow the perimeter of the groove with the flathead 3/32" screwdriver making sure to gently pry and lift upward until the control panel faceplate comes off.
  • Take your time prying off the control panel faceplate. If too much pressure is applied, the control panel faceplate can break.

Carefully wedge the flathead 3/32" screwdriver on the outer groove of the control panel faceplate.

Follow the perimeter of the groove with the flathead 3/32" screwdriver making sure to gently pry and lift upward until the control panel faceplate comes off.

Take your time prying off the control panel faceplate. If too much pressure is applied, the control panel faceplate can break.

1024

Step 2

  • Once the control panel faceplate is off, look for the Lock/Unlock tab located underneath the off button.
  • To unlock and release the control panel, insert the flathead 3/32" screwdriver into the tab and carefully push down. The control panel will then separate from the printer’s base by sliding it downward a little.

Once the control panel faceplate is off, look for the Lock/Unlock tab located underneath the off button.

To unlock and release the control panel, insert the flathead 3/32" screwdriver into the tab and carefully push down. The control panel will then separate from the printer’s base by sliding it downward a little.

Step 3

  • Underneath the control panel will be a flat grey ribbon cable. This cable is attached at the base of the green control board with the other end of the cable located on the back side of the printer’s base.
  • Carefully disconnect both ends of the flat grey ribbon cable to release the control panel in its entirety.
  • Only pull from the connector portion of the cable, as pulling on the wires may damage them.

Underneath the control panel will be a flat grey ribbon cable. This cable is attached at the base of the green control board with the other end of the cable located on the back side of the printer’s base.

Carefully disconnect both ends of the flat grey ribbon cable to release the control panel in its entirety.

Only pull from the connector portion of the cable, as pulling on the wires may damage them.

Step 4

  • Lift open the scanner lid and locate a black tab located at the center of the scanner bed.
  • Using your finger push (pull on some printers) the tab towards the scanner lid. This will release the scanner lid

Lift open the scanner lid and locate a black tab located at the center of the scanner bed.

Using your finger push (pull on some printers) the tab towards the scanner lid. This will release the scanner lid

Step 5

  • Once the scanner lid is removed use the Philips #1(Torx on some printers) Screwdriver to remove the screw.

Once the scanner lid is removed use the Philips #1(Torx on some printers) Screwdriver to remove the screw.

Step 6

  • Remove all four silver screws from the corners of the scanner glass cover with a T10 Torx Screwdriver.
  • Organization is everything. Remember to have your iFixit Magnetic Work Mat next to you. It will help keep screws organized and in place.

Remove all four silver screws from the corners of the scanner glass cover with a T10 Torx Screwdriver.

Organization is everything. Remember to have your iFixit Magnetic Work Mat next to you. It will help keep screws organized and in place.

Step 7

  • Once you have removed the four torx screws, gently lift the scanner glass cover from the printer’s base.

Once you have removed the four torx screws, gently lift the scanner glass cover from the printer’s base.

Step 8

              Scanner Lamp
  • Remove the scanner head from the scanner tray by lifting the scanner head up and pulling the black tab from the gray drive belt.

Remove the scanner head from the scanner tray by lifting the scanner head up and pulling the black tab from the gray drive belt.

Step 9

  • Turn the scanner upside down and place it on a level surface.
  • Remove the small silver screw in the scanner head’s control panel.

Turn the scanner upside down and place it on a level surface.

Remove the small silver screw in the scanner head’s control panel.

Step 10

  • Remove the control panel from the scanner head.

Remove the control panel from the scanner head.

Step 11

  • Remove the black face plate from the scanner head. Push on the two black tabs located on opposite sides of the scanner head. One of them is located in the groove the control panel normally rests in.

Remove the black face plate from the scanner head. Push on the two black tabs located on opposite sides of the scanner head. One of them is located in the groove the control panel normally rests in.

Step 12

  • Carefully twist white scanner lamp support out of its carriage and replace it with a new one.
  • Note: Scanner lamps are fragile and should be handled with care.

Carefully twist white scanner lamp support out of its carriage and replace it with a new one.

Note: Scanner lamps are fragile and should be handled with care.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Mackenzie Billings

Member since: 04/05/2011

541 Reputation

                                      2 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 12-31, Maness Spring 2011                        

                                                  Member of Cal Poly, Team 12-31, Maness Spring 2011 



                    CPSU-MANESS-S11S12G31                     


                                            5 Members                     


                                            9 Guides authored