Hp Psc 2410 Photosmart All In One Printer Encoder Strip Replacement Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          10 - 15 minutes            

Sections

2

• Scanner Tray
• 9 steps
• Encoder Strip
• 3 steps

Flags

3

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackHP PSC 2410 Photosmart All In One

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Remove Back Panel               

• Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

1024

Step 2

              Remove Inner Back Pannel               

• Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

Step 3

              Remove Upper Portion               

• Press down on the two plastic hinges to remove the upper portion of printer.

Press down on the two plastic hinges to remove the upper portion of printer.

Step 4

              Unplug Speaker Wire               

• Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

Step 5

              Removing Scanner Tray               

• Rotate the printer so the paper tray is facing towards you.
• Gently lift the scanner tray up and away from the printer.
• Press the gray plastic tabs inward to release the tabs from the printer.

Rotate the printer so the paper tray is facing towards you.

Gently lift the scanner tray up and away from the printer.

Press the gray plastic tabs inward to release the tabs from the printer.

Step 6

              Removing Scanner Tray - cont.               

• Returning to the back of the printer, remove the scanner from the back hinges.
• With pressure applied, the scanner will detach easily.

Returning to the back of the printer, remove the scanner from the back hinges.

With pressure applied, the scanner will detach easily.

Step 7

• Gently grasp and unplug the two white ribbon cables from the printer body.
• Be sure to grasp the cable at the connector and not to pull on the wires themselves.

Gently grasp and unplug the two white ribbon cables from the printer body.

Be sure to grasp the cable at the connector and not to pull on the wires themselves.

Step 8

• Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it’s port.
• Be sure to grasp the white connector and not to pull on the wires themselves.

Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it’s port.

Be sure to grasp the white connector and not to pull on the wires themselves.

Step 9

              Detaching the Scanner Tray               

• Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

Step 10

              Encoder Strip               

• Locate the panel labeled with a HP support link sticker.
• Release the tab by the support link sticker.
• Remove the black screw below the tab.

Locate the panel labeled with a HP support link sticker.

Release the tab by the support link sticker.

Remove the black screw below the tab.

Step 11

• Remove the two black screws closest to the printer tray.

Remove the two black screws closest to the printer tray.

Step 12

• Unhook the encoder strip from its small silver hooks and remove it from the printer.
• To replace, feed the new encoder strip through the silver hooks.

Unhook the encoder strip from its small silver hooks and remove it from the printer.

To replace, feed the new encoder strip through the silver hooks.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 8 other contributors 

                    Jeremy Mahrt                     

Member since: 05/08/2011

286 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       Cal Poly, Team 12-31, Maness Spring 2011                        

                                                  Member of Cal Poly, Team 12-31, Maness Spring 2011 



                    CPSU-MANESS-S11S12G31                     


                                            5 Members                     


                                            9 Guides authored