Hp Psc 2355 Scanner Glass Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Scanner Lid
2 steps
Scanner Glass
10 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

BackHP PSC 2355
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Scanner Lid

Grasp the scanner lid cover from the front of the device and lift lid all the way up until it stands on its own.

Grasp the scanner lid cover from the front of the device and lift lid all the way up until it stands on its own.

1024

Step 2

With two hands, grasp the lid on both sides near the hinges and lift straight up to release the lid from each hinge.

With two hands, grasp the lid on both sides near the hinges and lift straight up to release the lid from each hinge.

Step 3

              Scanner Glass

Once you have removed the scanner lid, locate the finger notch on the inside top left half of the bezel (control) panel cover.

Once you have removed the scanner lid, locate the finger notch on the inside top left half of the bezel (control) panel cover.

Step 4

Place your index finger in the notch and lift up to unsnap the panel.
Set panel cover aside.

Place your index finger in the notch and lift up to unsnap the panel.

Set panel cover aside.

Step 5

Use a T9 torx screwdriver to remove the 0.9 cm screw.

Use a T9 torx screwdriver to remove the 0.9 cm screw.

Step 6

From the front of the printer, remove the button panel by pulling it towards you while slightly lifting it up.

From the front of the printer, remove the button panel by pulling it towards you while slightly lifting it up.

Step 7

Disconnect the white ribbon cable by grasping it between your thumb and forefinger.
Gently pull to release the ribbon from the green circuit board.

Disconnect the white ribbon cable by grasping it between your thumb and forefinger.

Gently pull to release the ribbon from the green circuit board.

Step 8

Next, use a spudger to pry loose the flat ribbon computer cable by the plastic connection end and carefully separate it from the prongs on the button panel.
Now the whole button should be completely disconnected from the printer.
Set button panel aside.

Next, use a spudger to pry loose the flat ribbon computer cable by the plastic connection end and carefully separate it from the prongs on the button panel.

Now the whole button should be completely disconnected from the printer.

Set button panel aside.

Step 9

Using the T9 torx screwdriver, unscrew the seven 0.9 cm black screws on the top plastic frame around the glass.

Using the T9 torx screwdriver, unscrew the seven 0.9 cm black screws on the top plastic frame around the glass.

Step 10

From the back of the printer, locate the two large plastic tabs as shown.
With your index fingers underneath each tab, gently and simultaneously pull the tabs towards you and upwards to release the tabs from the plastic clasps behind them.
Once these tabs are released, you should be able to remove the whole plastic frame that holds the glass.

From the back of the printer, locate the two large plastic tabs as shown.

With your index fingers underneath each tab, gently and simultaneously pull the tabs towards you and upwards to release the tabs from the plastic clasps behind them.

Once these tabs are released, you should be able to remove the whole plastic frame that holds the glass.

Step 11

Gently lift the glass/plastic bed from the edge on the side opposite of the button/control panel section.
As shown in the second image, gently lift the glass pane up so that it is above the plastic tab that holds it into place.

Gently lift the glass/plastic bed from the edge on the side opposite of the button/control panel section.

As shown in the second image, gently lift the glass pane up so that it is above the plastic tab that holds it into place.

Step 12

Proceed to slide the glass pane out and over the plastic tab to remove it completely from the plastic bed.
Replace the glass with your new glass pane. To fully reassemble the printer, follow these instructions in reverse order.

Proceed to slide the glass pane out and over the plastic tab to remove it completely from the plastic bed.

Replace the glass with your new glass pane. To fully reassemble the printer, follow these instructions in reverse order.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Amber Gabaldon

Member since: 01/28/2014

343 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       New Mexico State, Team 1-4, Sheppard Spring 2014                        

                                                  Member of New Mexico State, Team 1-4, Sheppard Spring 2014 



                    NMSU-SHEPPARD-S14S1G4                     


                                            3 Members                     


                                            4 Guides authored

Bullets!#

Slice and Dice#

Introduction#

What you need#

Team#

Bullets!

Slice and Dice

Introduction

What you need

Team