Difficulty
Moderate
Steps
11
Time Required
10 minutes
Sections
2
- Scanner Lid
- 2 steps
- Button Panel
- 9 steps
Flags
0
BackHP PSC 2355
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Scanner Lid
- Grasp the scanner lid cover from the front of the device and lift lid all the way up until it stands on its own.
Grasp the scanner lid cover from the front of the device and lift lid all the way up until it stands on its own.
1024
Step 2
- With two hands, grasp the lid on both sides near the hinges and lift straight up to release the lid from each hinge.
With two hands, grasp the lid on both sides near the hinges and lift straight up to release the lid from each hinge.
Step 3
Button Panel
- Once you have removed the scanner lid, locate the finger notch on inside the top left half of the bezel (control) panel.
Once you have removed the scanner lid, locate the finger notch on inside the top left half of the bezel (control) panel.
Step 4
- Place your index finger in the notch and lift up to unsnap the panel.
- Set panel cover aside.
Place your index finger in the notch and lift up to unsnap the panel.
Set panel cover aside.
Step 5
- Use a T9 torx screwdriver to remove the 0.9 cm screw.
Use a T9 torx screwdriver to remove the 0.9 cm screw.
Step 6
- From the front of the printer, remove the button panel by pulling it towards you while slightly lifting it up.
From the front of the printer, remove the button panel by pulling it towards you while slightly lifting it up.
Step 7
- Disconnect the white ribbon cable by grasping it between your thumb and index finger.
- Gently pull to release the ribbon from the green circuit board
Disconnect the white ribbon cable by grasping it between your thumb and index finger.
Gently pull to release the ribbon from the green circuit board
Step 8
- Next, use the flat end of a spudger to pry loose the flat ribbon computer cable by the plastic connection end and carefully separate it from the prongs on the button panel.
- The entire button panel should now be completely disconnected from the printer.
Next, use the flat end of a spudger to pry loose the flat ribbon computer cable by the plastic connection end and carefully separate it from the prongs on the button panel.
The entire button panel should now be completely disconnected from the printer.
Step 9
- Lay the panel on a flat surface with the backside facing up.
- Using a T9 torx screwdriver, remove all six 0.7 cm silver screws from the off-white plastic panel.
Lay the panel on a flat surface with the backside facing up.
Using a T9 torx screwdriver, remove all six 0.7 cm silver screws from the off-white plastic panel.
Step 10
- Gently lift the button panel off the plastic backing with rubber button mat.
Gently lift the button panel off the plastic backing with rubber button mat.
Step 11
- Be careful not to lift out and lose the two clear plastic panel separators (these are not fastened to the panel but can easily fall out of the panel if tilted). These are two small plastic parts that sit near the top right and left portions of the panel.
- Insert your new button panel. To reassemble your printer, follow these instructions in reverse order.
Be careful not to lift out and lose the two clear plastic panel separators (these are not fastened to the panel but can easily fall out of the panel if tilted). These are two small plastic parts that sit near the top right and left portions of the panel.
Insert your new button panel. To reassemble your printer, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Patricia
Member since: 01/23/2014
143 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
TheFixers
Member of TheFixers
Community
2 Members
1 Guide authored
